Center Suspension Frame - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-9200 | Lever Puller Hoist | 3 |
B | 1P-0520 | Driver Group | 1 |
Show/hide table
Personal injury or death can result from improper lifting or blocking. When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component. Approximate weights of the components are shown. Clean all surfaces where parts are to be installed. |
Start By:
- Remove the center axle stabilizer rod.
- Remove bolts (1) and clamps (2).
Show/hide table
Illustration 2 g06133882 Typical Example - Attach Tooling (A) to the rear section of center suspension frame (3) on each side of the machine, as shown. The weight of center suspension frame (3) is approximately
153 kg (338 lb) .Show/hide tableIllustration 3 g06133883 Typical Example - Use a suitable bar and clevis to support Tooling (A). Attach Tooling (A) to the center suspension frame (3) as shown in Illustration 3. The weight of center suspension frame (3) is approximately
153 kg (338 lb) .Show/hide tableIllustration 4 g06133885 - Disconnect hose assembly (4).
- Remove nut (5), washer (6), and bolt (7).
Show/hide table
Illustration 5 g06133886 - Remove pin (8).
Show/hide table
Illustration 6 g06133887 - Use two people to remove bracket (11). The weight of bracket (11) is approximately
24 kg (53 lb) . - Remove bolts (9) and bracket (11) from center axle (10).
Show/hide table
Illustration 7 g06133890 - Remove bolts (12) from center axle (10).
- Use Tooling (A) to lower the center suspension frame to the ground. Lower and remove the center suspension frame from the center axle.
Show/hide table
Illustration 8 g06133894 - Remove bolts (13) and clamp ring (14).
Show/hide table
Illustration 9 g06133898 - Use Tooling (B) to remove bearing (15). Remove bearing (15).
Show/hide table
Illustration 1 | g06133880 |
- Install center suspension frame (3) in the reverse order of removal.
- Tighten bolts (12) and (9) to a torque of
900 ± 100 N·m (664 ± 74 lb ft) .
- Tighten bolts (12) and (9) to a torque of
Caterpillar Information System:
994K Wheel Loader Machine Systems Lift Cylinder - Remove and Install
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Ride Control Accumulator - Test and Charge
797F and 797F XQ Off-Highway Trucks Magnetic Plug (Pump Drive, Hydraulic) - Check
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B} M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Editing Truck and Material Lists
785G Off-Highway Truck Systems Electronic Control Module (ECM) - Replace
PM310, PM312, and PM313 Cold Planer Legs (Struts) - Lubricate
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil Sample - Obtain
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil Level - Check
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil Filter - Replace
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil - Change
PM310, PM312, and PM313 Cold Planer Fuel Tank Water and Sediment - Drain
2570D and 2670D Wheel Feller Buncher Engine Supplement Engine - Remove and Install
C175–16 Locomotive Engine Air in Fuel - Test
An Improved Paint Masking Process Is Now Used on the Front Axle Steering Cylinders for Certain Backhoe Loaders {4303, 4313} An Improved Paint Masking Process Is Now Used on the Front Axle Steering Cylinders for Certain Backhoe Loaders {4303, 4313}
725C2 and 730C2 Articulated Truck Machine System Rear Suspension Frame - Remove and Install
MD6200 Rotary Drill Cab Air Filter (Fresh Air) - Clean/Replace
An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251} An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251}
PM310, PM312, and PM313 Cold Planer Rotor Drive Belt - Inspect
PM310, PM312, and PM313 Cold Planer Rotor Drive Clutch Bearings - Lubricate
PM310, PM312, and PM313 Cold Planer Steering Cylinder Ends - Lubricate
New Hose Clamps are Now Used in the Coolant Lines Group of Certain 700 Series Articulated Trucks {1087, 1380} New Hose Clamps are Now Used in the Coolant Lines Group of Certain 700 Series Articulated Trucks {1087, 1380}
PM310, PM312, and PM313 Cold Planer Water Spray System - Inspect
563D and 573D Wheel Feller Buncher Machine Systems Control Manifold (Hydraulic Fan) - Remove and Install