New Hose Clamps are Now Used in the Coolant Lines Group of Certain 700 Series Articulated Trucks {1087, 1380}
- Articulated Truck
- 725C (S/N: T261-90105; TFB1-833)
- 725C2 (S/N: 2T31-112; TA71-90104)
- 730C (S/N: T281-104; TFF1-1410)
- 730C EJECTOR (S/N: TFH1-160)
- 730C2 (S/N: 2T41-123)
- 730C2 EJ (S/N: 2T51-131)
- 735C (S/N: TFJ1-221)
- 740C EJECTOR (S/N: TFN1-178)
- 745C (S/N: JE81-116; TFK1-1300)
- 725C2 (S/N: 2T31-112; TA71-90104)
Description Of Change: New hose clamps are now used in the coolant lines group of the products listed above. The new hose clamps will increase clamping force and prevent leaking.
Adaptable To: The following changes are adaptable to the products within the listed serial numbers, and are effective with all products after the listed serial numbers.
Show/hide table
Parts Required | ||||
Item | Qty | Part Number | Description | Former Part Number |
1 | 4 | Clamp | ||
4 | Clamp |
- If hose o.d. is less than
13.3 mm (0.52 inch) , then use 510-2512 Clamp. - If hose o.d. is greater than 13.3 mm, then use 539-1248 clamp. Also if the larger diameter hose is used, then 3U-2752 Clip will need to be replaced by 344-5360 Clip.
Show/hide table
Qty | Part Number | Description |
1 | Plier Tool |
- Remove and discard four existing 431-9388 Clamps and replace with four clamps (1) that fit 332-7785 Hose. Refer to Illustration 1, Illustration 2, and Illustration 3 for detailed views of the clamp locations.
- Crimp clamps (1) into place using plier tool (A).
Note: After new clamps (1) are installed, run the machine and check for leaks.
Show/hide table
Illustration 1 | g06135963 |
Hose connection (1) |
Show/hide table
Illustration 2 | g06135968 |
Top view showing upper hose connection (1) |
Show/hide table
Illustration 3 | g06135972 |
Bottom view showing lower hose connection (1) |
Caterpillar Information System:
PM310, PM312, and PM313 Cold Planer Steering Cylinder Ends - Lubricate
PM310, PM312, and PM313 Cold Planer Rotor Drive Clutch Bearings - Lubricate
PM310, PM312, and PM313 Cold Planer Rotor Drive Belt - Inspect
An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251} An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251}
MD6200 Rotary Drill Cab Air Filter (Fresh Air) - Clean/Replace
725C2 and 730C2 Articulated Truck Machine System Rear Suspension Frame - Remove and Install
An Improved Paint Masking Process Is Now Used on the Front Axle Steering Cylinders for Certain Backhoe Loaders {4303, 4313} An Improved Paint Masking Process Is Now Used on the Front Axle Steering Cylinders for Certain Backhoe Loaders {4303, 4313}
C175–16 Locomotive Engine Air in Fuel - Test
2570D and 2670D Wheel Feller Buncher Engine Supplement Engine - Remove and Install
725C2 and 730C2 Articulated Truck Machine System Center Suspension Frame - Remove and Install
994K Wheel Loader Machine Systems Lift Cylinder - Remove and Install
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Ride Control Accumulator - Test and Charge
PM310, PM312, and PM313 Cold Planer Water Spray System - Inspect
563D and 573D Wheel Feller Buncher Machine Systems Control Manifold (Hydraulic Fan) - Remove and Install
PM310, PM312, and PM313 Cold Planer Water Spray System Fluid Level - Check
MH3037 Material Handler Engine Supplement Turbocharger - Remove and Install - Second Stage Turbocharger
CP54B, CS54B and CS64B Soil Compactors Machine Systems Operator Controls (Vibratory System)
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Electric Drive Pump (Powered Stairway) Oil Level - Check - If Equipped
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Manual Lowering (Powered Stairway) - Test - If Equipped
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Platform (Powered Stairway) - Lubricate - If Equipped
730C2 and 725C2 Articulated Truck Power Train Front Axle - Remove and Install
PM310, PM312, and PM313 Cold Planer Lower Conveyor Deflectors (First Stage) - Inspect/Replace
PM310, PM312, and PM313 Cold Planer Moldboard Cutting Edge - Inspect/Adjust/Replace
PM310, PM312, and PM313 Cold Planer Rotor Bearing Oil - Change