Muffler - Remove and Install
Removal Procedure
- Open the engine access door.
- Release the latch on the radiator. Raise the radiator. This will allow access to the muffler.
Note: Do not attempt to service the muffler until the engine is cool to the touch.
- Remove three bolts (1) and the gasket.
Note: The gasket may be attached to the exhaust manifold.
Show/hide table
Illustration 1 | g00594699 |
- Disconnect exhaust elbow (2) from exhaust manifold (3) .
- Remove four bolts (4). Remove muffler (5) from the machine.
Show/hide table
Illustration 2 | g00594714 |
- Remove clamp (6). Separate exhaust elbow (2) from muffler (5) .
Show/hide table
Illustration 3 | g00594720 |
Installation Procedure
- Install clamp (6) in order to secure exhaust elbow (2) to muffler (5) .
Show/hide table
Illustration 4 | g00594720 |
- Place muffler (5) in position. Install four bolts (4) in order to secure muffler (5) to the machine.
Show/hide table
Illustration 5 | g00594714 |
- Align exhaust elbow (2) to exhaust manifold (3). Apply 5P-3931 Anti-Seize Compound to three bolts (1). Install the new gasket and three bolts (1) in order to secure exhaust elbow (2) to the exhaust manifold (3) .
Show/hide table
Illustration 6 | g00594699 |
- Start the engine and check for exhaust leaks.
- Turn the engine to the OFF position. Lower the radiator and lock the radiator into position.
- Close the engine access door.
Caterpillar Information System:
725 and 730 Articulated Trucks Fuses - Replace
CS-431C, CP-433C and CS-433C Vibratory Compactors Propel System Wheel and Tire
2006/03/27 The Differential and Bevel Gear Group Has Been Updated {3251, 3258}
140H and 160H Motor Graders Cutting Edges and End Bits - Inspect/Replace
725 and 730 Articulated Trucks Hoist, Steering, and Brake System Oil Level - Check
988G Wheel Loader Power Train Differential and Bevel Gear - Assemble
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Senders
3408E and 3412E Engines for Caterpillar Built Machines Camshaft Bearings - Remove
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Sensors
AP-1000B and BG-260C Asphalt Pavers Auxiliary System Shutoff Valve (Ventilation System)
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Cut Off Shoe Installation
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Power Train Traction Control System
120H Motor Grader Cutting Edges and End Bits - Inspect/Replace
3408E and 3412E Engines for Caterpillar Built Machines Camshaft Bearings - Install
797 Off-Highway Truck Power Train Transmission Hydraulic Control - Assemble
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Screed Plate Adjustment
CB-634C Vibratory Compactor Changing Engine Speed
2000/03/20 Corrections to the Power Train Disassembly and Assembly Module, SENR1217, Power Train Disassembly and Assembly Module, SENR5976-01, Power Train Disassembly and Assembly Module, SENR5995-01, Power Train Disassembly and Assembly Module, SENR6706-01, Po
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Related Components
216, 226 and 228 Skid Steer Loaders Engine Supplement Electric Starting Motor - Remove and Install - 228 Skid Steer Loader
16H Motor Grader Cutting Edges and End Bits - Inspect/Replace
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Governor Actuator Control
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Deflector Plate Adjustment
2000/03/06 The End Of Control Cable For Implement Valve Has Serviceable Parts {5051}