Deflector Plate Adjustment
Show/hide table
 |
Personal injury can result from rotating and moving parts. Stay clear of all rotating and moving parts. Never attempt adjustments while the machine is moving or the engine is running unless otherwise specified. The machine must be parked on a level surface and the engine stopped. Attach a "Do Not Operate" or similar warning tag to the start switch and controls before servicing, repairing, or making adjustments to the machine. |
 |
The deflector plate must be adjusted so the edge of the plate is at the top of the radius of the nose piece.
- Loosen the locknuts (2) in order to adjust the deflector plate (3) .
Show/hide table
 | |
| Illustration 1 | g00686187 |
- Use the adjustment rods (1) to position the deflector plate (3). Adjust the rods until the edge of the plate is at the top of the radius on the nose piece.
- With the plate in the proper position, tighten the locknuts (2) .
Caterpillar Information System:
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Governor Actuator Control
16H Motor Grader Cutting Edges and End Bits - Inspect/Replace
216, 226 and 228 Skid Steer Loaders Engine Supplement Electric Starting Motor - Remove and Install - 228 Skid Steer Loader
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Related Components
2000/03/20 Corrections to the Power Train Disassembly and Assembly Module, SENR1217, Power Train Disassembly and Assembly Module, SENR5976-01, Power Train Disassembly and Assembly Module, SENR5995-01, Power Train Disassembly and Assembly Module, SENR6706-01, Po
CB-634C Vibratory Compactor Changing Engine Speed
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Screed Plate Adjustment
797 Off-Highway Truck Power Train Transmission Hydraulic Control - Assemble
3408E and 3412E Engines for Caterpillar Built Machines Camshaft Bearings - Install
120H Motor Grader Cutting Edges and End Bits - Inspect/Replace
216, 226 and 228 Skid Steer Loaders Engine Supplement Muffler - Remove and Install
725 and 730 Articulated Trucks Fuses - Replace
2000/03/06 The End Of Control Cable For Implement Valve Has Serviceable Parts {5051}
2000/03/06 The VIMSpc99 Version 1.1.7 Software Update Is Now Available {7601}
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Solenoid Valves
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Cut Off Shoes
16H Motor Grader Drawbar Ball and Socket - Lubricate
D8R Series II Track-Type Tractor Engine Valve Rotators - Inspect
140H and 160H Motor Graders Drawbar Ball and Socket - Lubricate
3508B Engine for 854G Wheel Dozers and 992G Wheel Loaders Permanent Timing Calibration Sensor
C-12, C-15 and C-16 Engines for Caterpillar Built Machines CID 0001 FMI 11 Injector Cylinder #1 fault
120H Motor Grader Drawbar Ball and Socket - Lubricate
TK1051 Track Feller Buncher Air Conditioner/Cab Heater Filter (Recirculation) - Inspect/Replace
228 and 248 Skid Steer Loaders Machine Systems Line Relief Valve - Test and Adjust