8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Caterpillar


Cut Off Shoe Installation

Usage:

8-16B 2JN
Note: When you use cut off shoes, you must readjust the feeder control paddles due to the reduction in width.


NOTICE

When you pave, do not force excessive material onto the cut-off shoes. This will increase the drag and put exessive strain on the end gate. Damage to the end gate may occur.



NOTICE

Unlock the cut-off shoes from the end gates before you raise the screed for travel. This will prevent the cut-off shoes from contacting the auger conveyor.





    Illustration 1g00685234

  1. Select the proper shoe for the desired width. Raise the end gate.

  1. Place the cut off shoe on the end gate for the amount of reduction that is desired.

  1. Lower the end gate (1) onto the cut off shoe.

  1. Install the stud (3) in the slotted hole (4) on the end gate. Install the bolt (2) in the hole on the end gate.

Caterpillar Information System:

550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Power Train Traction Control System
CB-535B Vibratory Compactor Vibratory System Relief Valve (Pressure Override) - Test and Adjust
725 and 730 Articulated Trucks Hoist, Steering, and Brake System Breather - Inspect/Replace
2000/03/13 Serviceable Parts of the Fuel Injection Pump {1251, 1251}
988G Wheel Loader Power Train Differential and Bevel Gear - Install - Rear
824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Hydraulic System Vane Pump (Implement)
2000/05/01 New Axle Housings Increase the Parts' Commonality {3259, 3260, 3278}
725 and 730 Articulated Trucks Oscillating Hitch - Lubricate
Installation of the 172-9321 Metering Pump for the Steering System{4312} Installation of the 172-9321 Metering Pump for the Steering System{4312}
784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D, 797 and 797B Off-Highway Trucks VIMS &trade; Switch Circuits
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Before Paving Setup
2000/03/06 An Improved Input Pinion Is Now Used {3254, 3256, 3258}
AP-1000B and BG-260C Asphalt Pavers Auxiliary System Shutoff Valve (Ventilation System)
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Sensors
3408E and 3412E Engines for Caterpillar Built Machines Camshaft Bearings - Remove
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Senders
988G Wheel Loader Power Train Differential and Bevel Gear - Assemble
725 and 730 Articulated Trucks Hoist, Steering, and Brake System Oil Level - Check
140H and 160H Motor Graders Cutting Edges and End Bits - Inspect/Replace
2006/03/27 The Differential and Bevel Gear Group Has Been Updated {3251, 3258}
CS-431C, CP-433C and CS-433C Vibratory Compactors Propel System Wheel and Tire
725 and 730 Articulated Trucks Fuses - Replace
216, 226 and 228 Skid Steer Loaders Engine Supplement Muffler - Remove and Install
120H Motor Grader Cutting Edges and End Bits - Inspect/Replace
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.