Hydraulic Tank
Show/hide table
 | |
| Illustration 1 | g00664503 |
Capacity ... 91 L (24 US gal)
(1) Torque for the temperature sensor ... 75 ± 7 N·m (55 ± 5 lb ft)
(2) Apply 5P-3413 Pipe Sealant to the threads on the breather.
Torque for the breather ... 10 ± 1 N·m (89 ± 9 lb in)
Note: In order for the breather to have enough clearance, the breather should not be higher than 64 mm (2.52 inch) above the tank.
(3) Torque for the hydraulic tank sight gauge ... 7 ± 1 N·m (62 ± 9 lb in)
(4) The torque for the nuts on the four tank mounting bolts. ... 50 ± 10 N·m (37 ± 7 lb ft)
(5) Apply 5P-3413 Pipe Sealant to the threads on the strainer.
(6) Apply 5P-3413 Pipe Sealant to the threads on the adapter.
Caterpillar Information System:
2000/01/24 Change to the Torque Specification for the Drive Shaft Bolts in Disassembly and Assembly Manuals, SENR6768 and SENR1217 {3253}
924G and 924GZ Wheel Loaders Power Train Differential - Assemble
3034 Engine for Caterpillar Built Machines Fuel Shutoff Solenoid
924G and 924GZ Wheel Loaders Power Train Differential - Disassemble
924G and 924GZ Wheel Loaders Machine Systems Brake Control Valve (Service) - Remove and Install
824G Wheel Tractor, 825G Soil Compactor and 826G Landfill Compactor Hydraulic System Pilot System Pressure - Test
CP-433C, CS-431C and CS-433C Paving Compactors Axle Oil Sample - Obtain
1999/12/01 New Engine News Format {0374}
3508B Engine for Caterpillar Built Machines Crankshaft Wear Sleeves and Seals
2000/01/31 New Electronic Control Module (ECM) Provides Improved Reliability {1901}
2000/02/21 The New 10.0X Class of VIMS Onboard Software and the New Version 4.0 VIMS Hardware {7610, 7620}
988G Wheel Loader Power Train Relief Valve (Transmission Hydraulic Control)
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train Engagement Pressure for the Transmission Clutch - Calibrate
966G Wheel Loader and 972G Wheel Loader Power Train Reverse High Speed Lockout - Program
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train Calibration and Programming
CP-433C, CS-431C and CS-433C Paving Compactors Drum Scrapers - Inspect/Adjust/Replace
D400E Series II Articulated Truck Power Train General Information
2000/01/17 Production Process Change Eliminates Antirotation Retaining Pin In Rear Wheel Station {4201}
CP-433C, CS-431C and CS-433C Paving Compactors Engine Oil and Filter - Change
228 and 248 Skid Steer Loaders Machine Systems General Information
988G Wheel Loader Power Train Bypass Switch (Power Train Oil Filter)
Installation and Removal Procedure for the Padded Shell Kit Attachment{6605} Installation and Removal Procedure for the Padded Shell Kit Attachment{6605}
1999/12/13 Rollover Protection Structures (ROPS) Are Now Available {7325}
1999/12/20 A Lubricant Has Been Added to the Splines of the Pump Drive Gearbox {3108}