Support Bracket for the Rotary Beacon Interferes With the Cab Caterpillar

Support Bracket for the Rotary Beacon Interferes With the Cab

Usage:

Support Bracket for the Rotary Beacon Interferes With the Cab

CONFIDENTIAL TIBU2672-00

Show/hide table

TECHNICAL INFORMATION BULLETIN	August 06, 2003
Motor Graders	120H (2AN1-Up) 12H (2WR1-Up) 140H (9ZN1-Up)
Component Code(s)	1431

SUBJECT: Support Bracket for the Rotary Beacon Interferes With the Cab

PROBLEM:

The front edge of the 129-8970 Bracket for the rotary beacon is contacting the top of the cab. This is allowing the transmission of noise from the rotation of the beacon into the cab.

SOLUTION:

Grind the beacon guard assembly as necessary in order to gain the necessary clearance between the top of the cab and the guard. Touch up the affected area using 4C-4200 Paint.

Illustration 1

COPYRIGHT 2003 CATERPILLAR
ALL RIGHTS RESERVED

Caterpillar Information System:

HYDRAULIC TANK FILLER TUBE STRAINER MAY RUST HYDRAULIC TANK FILLER TUBE STRAINER MAY RUST

Inspection of the Gear Pump for the Hoist on the 797 Off-Highway Trucks is Required Inspection of the Gear Pump for the Hoist on the 797 Off-Highway Trucks is Required

New Method of Engaging the Parking Brake on Motor Graders New Method of Engaging the Parking Brake on Motor Graders

Drive Shaft U-Joint Bolts May Not Have the Proper Torque on Certain Motor Graders Drive Shaft U-Joint Bolts May Not Have the Proper Torque on Certain Motor Graders

New Method for Shipping Mirrors for the Motor Graders New Method for Shipping Mirrors for the Motor Graders

Requesting Information on Motor Grader Films Requesting Information on Motor Grader Films

Use Only 6 Micron Filters on the Transmissions for the Newer Motor Graders Use Only 6 Micron Filters on the Transmissions for the Newer Motor Graders

777D Final Drive Wear on bearing and/or Thrust Plate 777D Final Drive Wear on bearing and/or Thrust Plate

HOIST CONTROL VALVE ELECTRICAL CONNECTORS MAY GET MATCHED INCORRECTLY HOIST CONTROL VALVE ELECTRICAL CONNECTORS MAY GET MATCHED INCORRECTLY

185-3628 ; 185-3629 STEERING SHAFTS MUST BE INSPECTED PRIOR TO INSTALLATION 185-3628 & 185-3629 STEERING SHAFTS MUST BE INSPECTED PRIOR TO INSTALLATION

The 192-7887 Guard That is Under the Right Hand Platform has been Removed The 192-7887 Guard That is Under the Right Hand Platform has been Removed

Certain Air Dryers Should be Removed From Dealer Inventory Certain Air Dryers Should be Removed From Dealer Inventory

Spark Arrestor Muffler Failure Spark Arrestor Muffler Failure

THE MAGNETS ON THE 178-5062 MAGNETIC SCREEN MAY LOOSEN IN OPERATION THE MAGNETS ON THE 178-5062 MAGNETIC SCREEN MAY LOOSEN IN OPERATION

192-9969 BEARING AND 192-9970 BEARING MAY HAVE BEEN MANUFACTURED INCORRECTLY 192-9969 BEARING AND 192-9970 BEARING MAY HAVE BEEN MANUFACTURED INCORRECTLY

Two Lubrication Holes Have Been Omitted In the 7S-8580 Rotation Clutch Carrier Two Lubrication Holes Have Been Omitted In the 7S-8580 Rotation Clutch Carrier

Some 2P-4472, 7G-0825, and 8P-1656 Clutch Plates May Have Been Shipped Into the Parts System Before Finish Grinding Some 2P-4472, 7G-0825, and 8P-1656 Clutch Plates May Have Been Shipped Into the Parts System Before Finish Grinding

Logged Codes Must Be Cleared During Pre-delivery Inspections Logged Codes Must Be Cleared During Pre-delivery Inspections

THE ALTERNATOR PULLEY MAY BE ASSEMBLED INCORRECTLY THE ALTERNATOR PULLEY MAY BE ASSEMBLED INCORRECTLY

THE HOSE THAT CONNECTS THE CASE TO THE TRANSMISSION MAY NOT SEAL PROPERLY THE HOSE THAT CONNECTS THE CASE TO THE TRANSMISSION MAY NOT SEAL PROPERLY

030-7965 ELBOW MAY BE MISSING FROM RADIATOR GROUP 030-7965 ELBOW MAY BE MISSING FROM RADIATOR GROUP

2ND REDUCTION FINAL DRIVE BEARINGS MAY FAIL PREMATURELY 2ND REDUCTION FINAL DRIVE BEARINGS MAY FAIL PREMATURELY

THE BLOWER RESISTER MAY BE WIRED INCORRECTLY THE BLOWER RESISTER MAY BE WIRED INCORRECTLY

2ND REDUCTION FINAL DRIVE BEARING MAY FAIL PREMATURELY 2ND REDUCTION FINAL DRIVE BEARING MAY FAIL PREMATURELY