Transfer Idler Gear Bearing Failures
Usage:
MOTOR GRADERS16H (6ZJ),
14H (7WJ),
16G (93U),
14G (96U) MOTOR GRADERS
14H (7WJ),
16G (93U),
14G (96U) MOTOR GRADERS
Problem:
The (6M-9497) Roller Bearing Assembly in the idler gear that is within transfer gear case, has been failing prematurely. Analysis has revealed movement between the two bearing cups and the cup spacer (current cup spacer being non-hardened). This movement causes spacer wear allowing the bearing to loose adjustment and fail.
Solution:
The 9M-9497 Roller Bearing Assembly has been canceled and replaced by 165-0002 Bearing. The new 165-0002 Bearing has a hardened cup spacer to eliminate the possibility of wearing and getting out of adjustment. The new 165-0002 Bearing is now available.
COPYRIGHT 1999 CATERPILLAR ALL RIGHTS RESERVED
Caterpillar Information System:
Locknut Coming Loose On Directional Clutch Hubs Locknut Coming Loose On Directional Clutch Hubs
Rework Kit Available To Stiffen Main Frame Rework Kit Available To Stiffen Main Frame
Roller Retainer Bolt Loosening Roller Retainer Bolt Loosening
Improperly Torqued Driveshaft Yoke Hardware Improperly Torqued Driveshaft Yoke Hardware
Tire Shortages For Backhoe Loaders Tire Shortages For Backhoe Loaders
Erratic Engine Oil Pressure Readings Erratic Engine Oil Pressure Readings
Missing Rear Gear Train Idler Shaft Mounting Bolt Seals May Result In Oil Leaks Missing Rear Gear Train Idler Shaft Mounting Bolt Seals May Result In Oil Leaks
Backhoe Loader Steering Cylinder May Malfunction Backhoe Loader Steering Cylinder May Malfunction
Leave Bolts Installed If Removing Front Counterweight Bracket Leave Bolts Installed If Removing Front Counterweight Bracket
New Drum Edge Profile May Minimize Mat Marking With Fine "Mixes" New Drum Edge Profile May Minimize Mat Marking With Fine "Mixes"
Correct Service Replacement Part Numbers For 100-5778 Caterpillar Monitoring System Control Correct Service Replacement Part Numbers For 100-5778 Caterpillar Monitoring System Control
Alternator Drive Belt Retention Alternator Drive Belt Retention
Difficult Installation Of Upper Hook Sheave Block Difficult Installation Of Upper Hook Sheave Block
Difficult Installation Of Upper Hook Sheave Block Link Difficult Installation Of Upper Hook Sheave Block Link
Clogged Atmospheric Pressure Sensors Clogged Atmospheric Pressure Sensors
Tooth Wear On 6Y5914 (Rotating) Clutch Disc Tooth Wear On 6Y5914 (Rotating) Clutch Disc
Service Replacement Of Electronic Monitoring System (EMS) Module May Also Require Installation Of New Engine Software Service Replacement Of Electronic Monitoring System (EMS) Module May Also Require Installation Of New Engine Software
Certain Pavers May Have The Material Height Dial Buffers Located In The Screed Control Boxes Wired Wrong Certain Pavers May Have The Material Height Dial Buffers Located In The Screed Control Boxes Wired Wrong
Baffle Assemblies May Work Loose In Hydraulic Tank Baffle Assemblies May Work Loose In Hydraulic Tank
Some Rear Suspension Cylinders May Have Oversize Bores For The Eye Bearings Some Rear Suspension Cylinders May Have Oversize Bores For The Eye Bearings
New Information Is Now Available For The 3524B Engine New Information Is Now Available For The 3524B Engine
New Information Is Now Available For The 3524B Engine Coupling New Information Is Now Available For The 3524B Engine Coupling
Front And Rear Suspension Cylinder Nitrogen And Oil Charging Procedure Changes Front And Rear Suspension Cylinder Nitrogen And Oil Charging Procedure Changes
Rear Axle Lubrication Motor Leakage Issues Rear Axle Lubrication Motor Leakage Issues