1996/12/30 Caterpillar

Supplement To Operation And Maintenance Manual; "Dual Position Switch To Operate The Tilt Kickout System" {1435,7451}

Usage:

IT38F (6FN1-Up) Integrated Toolcarrier

Reference: Operation And Maintenance Manual, SEBU6872-01, IT38F Integrated Toolcarrier; Page 46, Operation Section-Attachment Controls, "Fourth Valve Function (Attachment)".

The dual position switch to operate the tilt kickout system (Item 1), is shown incorrectly in the illustration in the section "Fourth Valve Function (Attachment)" (SEBU6872-01, Page 46). The correct switch for the tilt kickout system is shown in the following illustration.

Illustration 1. Correct switch (1) for dual position operation of the tilt kickout system.

Also, the information that follows should be used to supplement the tilt kickout information in the section "Fourth Valve Function (Attachment)".

The dual position switch (1) for the tilt kickout system allows the operator to change from the first implement to the second implement, without having to adjust again the position of the switches in the positioner control group.

Caterpillar Information System:

1996/12/30 Procedure For Aligning Front Suspension Frame Group With Output Transfer Gearbox {7200}

1996/12/30 New Hydraulic Pump Group Increases Service Life {5070}

1996/12/30 Improved Seals And Bearings Used To Reduce Seal Leaks In Output Transfer Gear Groups {3159,3003}

1996/12/30 Seal Improvement Prevents Leakage In Hook Winch Groups {5417}

1996/12/30 3054 Engine - New Rear Crankshaft Oil Seal Housing Provides Better Seal {1161}

1996/12/30 Description Of August 1996 (AUG96) Personality Module Changes For 3176B (43Z), 3176C (7ZR), And 3196 (6AR) Engines {1902,1901,1923,7414}

1996/12/23 New Rotocoil Assembly Used In Engine Cylinder Head Groups{1109}

1996/12/23 New Telehandler Brake Pack Adjustment Procedure For Rebuilt Brake Groups{4251,4004,4255,4261}

1996/12/23 New Temperature Sensors Used Which Prevent False Over Temperature Warnings{1906,1400}

1996/12/23 Torque/Turn Method Used To Tighten Brake Caliper Retaining Bolts{4256}

1996/12/23 Improved Seals And Bearings Used To Reduce Seal Leaks In Transfer Gear Groups (6WD){3250}

1996/12/23 Orificed Check Valve Removed From Hoist Cylinder Groups For Truck Bed{5102,5486}

1996/12/30 Improved Boom Electrical Harness Routing For Increased Reliability {1408}

1996/12/30 Flywheel Housing To Cylinder Block Joint Improvements {1157,1201}

1997/01/13 1U-9095 Lifter Group Allows Complete Undercarriage To Be Moved With Fork Lift Or Farm Tractor{4150,0632}

1997/01/13 1U-6130 Guide Stud, 1U-9785 Guide Stud And 1U-9817 Guide Stud Makes Undercarriage Installation And Removal Much Easier And More Efficient{4150,0729}

1997/01/13 1U-9055 Idler Lifter Removes And Installs Front Idler Assembly Using Overhead Lifting Equipment{4150,0729}

1997/01/13 Use 1U-9097 Wrench To Remove And Install Accumulator In Mobile-Trac Tensioning System{4197,0756}

1997/01/13 1U-9054 Driver Lifter Removes And Installs Rear Drive Wheel Assembly Using Overhead Lifting Equipment{4199,0729}

1997/01/13 1U-9058 Hose Group Provides All Necessary Equipment For Adjusting And Releasing Tension On Mobile-Trac Belts{4197,0766}

1997/01/13 Use 125-4634 Spanner Wrench Assembly To Remove And Install 110-5425 Nut Retaining Axle Shaft Into Housing{3250,0727}

1997/01/13 Spanner Wrenches And Related Tools To Remove And Install Final Drive Bearing Locknut{4050,0602}

1997/01/13 Use 126-6611 Seal Driver To Install Outboard Oil Seal On Eccentric Group{6605,6606,0727}

1997/01/13 129-7142 Lifting Beam Simplifies Removal And Installation Of Friction Group{6605,0632,0717}