1997/01/13 Caterpillar

1U-9095 Lifter Group Allows Complete Undercarriage To Be Moved With Fork Lift Or Farm Tractor{4150,0632}

Usage:

Challenger 35, Challenger 45, Challenger 55 Agricultural Tractors

Reference: Service Manual; SENR8300; Challenger 35, 45 and 55 Agricultural Tractors.

Warranty: G

Features/Benefits

* Used to lift and move complete Challenger (right or left) undercarriage - speeds up gauge changes (gauge is the width between track belts)

* Used with forklift or farm tractor with three-point hitch (fits category 2, 3N, and 3 quick hitches)

* Three point hitch mounting hardware is movable to fit different hitch designs

* Center tube of lifter group fits into counterweight tube mounting hole (counterweights and counterweight mounting tube must be removed)

* Three legs are used only to support lifting group when not in use (locked into place using pin with 1U-9096 Snap Pin)

* Two bolts help to level lifting group on forks of fork lift

1U-9095 Lifter Group (1) Eight 8T-6671 Bolts and eight 7X-0448 Nuts. (2) Six 7B-2725 Bolts. (3) Three 1U-9096 Snap Pins. (4) 1U-9289 Leg Assembly

Caterpillar Information System:

1996/12/30 Flywheel Housing To Cylinder Block Joint Improvements {1157,1201}

1996/12/30 Improved Boom Electrical Harness Routing For Increased Reliability {1408}

1996/12/30 Supplement To Operation And Maintenance Manual; "Dual Position Switch To Operate The Tilt Kickout System" {1435,7451}

1996/12/30 Procedure For Aligning Front Suspension Frame Group With Output Transfer Gearbox {7200}

1996/12/30 New Hydraulic Pump Group Increases Service Life {5070}

1996/12/30 Improved Seals And Bearings Used To Reduce Seal Leaks In Output Transfer Gear Groups {3159,3003}

1996/12/30 Seal Improvement Prevents Leakage In Hook Winch Groups {5417}

1996/12/30 3054 Engine - New Rear Crankshaft Oil Seal Housing Provides Better Seal {1161}

1996/12/30 Description Of August 1996 (AUG96) Personality Module Changes For 3176B (43Z), 3176C (7ZR), And 3196 (6AR) Engines {1902,1901,1923,7414}

1996/12/23 New Rotocoil Assembly Used In Engine Cylinder Head Groups{1109}

1996/12/23 New Telehandler Brake Pack Adjustment Procedure For Rebuilt Brake Groups{4251,4004,4255,4261}

1996/12/23 New Temperature Sensors Used Which Prevent False Over Temperature Warnings{1906,1400}

1997/01/13 1U-6130 Guide Stud, 1U-9785 Guide Stud And 1U-9817 Guide Stud Makes Undercarriage Installation And Removal Much Easier And More Efficient{4150,0729}

1997/01/13 1U-9055 Idler Lifter Removes And Installs Front Idler Assembly Using Overhead Lifting Equipment{4150,0729}

1997/01/13 Use 1U-9097 Wrench To Remove And Install Accumulator In Mobile-Trac Tensioning System{4197,0756}

1997/01/13 1U-9054 Driver Lifter Removes And Installs Rear Drive Wheel Assembly Using Overhead Lifting Equipment{4199,0729}

1997/01/13 1U-9058 Hose Group Provides All Necessary Equipment For Adjusting And Releasing Tension On Mobile-Trac Belts{4197,0766}

1997/01/13 Use 125-4634 Spanner Wrench Assembly To Remove And Install 110-5425 Nut Retaining Axle Shaft Into Housing{3250,0727}

1997/01/13 Spanner Wrenches And Related Tools To Remove And Install Final Drive Bearing Locknut{4050,0602}

1997/01/13 Use 126-6611 Seal Driver To Install Outboard Oil Seal On Eccentric Group{6605,6606,0727}

1997/01/13 129-7142 Lifting Beam Simplifies Removal And Installation Of Friction Group{6605,0632,0717}

1997/01/13 Fixture Assembly Allows More Accurate Levelling Of Screed Plates{6643,0764}

1997/01/13 More Collets Now Available For XT5 And XT6 Hoses Using 4C-9480 Hose Tooling Group{0684}

1997/01/13 Use 126-1023 Stem Pusher For Sleeve And Coupling Removal On Hose Assemblies{5057,0684}