1997/01/13 Caterpillar

Use 126-6611 Seal Driver To Install Outboard Oil Seal On Eccentric Group{6605,6606,0727}

Usage:

CB-534, CB-534B, CB-535 CB-634 Asphalt Compactors

Reference: Compactor Service Manual, Disassembly and Assembly of Eccentric Group.

Warranty: G

Features/Benefits

* Used to properly install 081-3948 and 105-6145 Seals (or similar seal) into housing of eccentric group

* Driver quickly and easily installs seal, flush with housing, without possibility of damage (eliminates hammer and punch method)

* Seal can be installed with eccentric group on the machine from the drive input side only (eliminates tear-down of drum just for seal change)

* Designed to fit into hard-to-reach seal location

* Lead-in chamfer allows driver to easily slip onto shaft and over wear sleeve

Specifications/Technical Information

Outside diameter - 92 mm (3.6 inch)

Inside diameter - 68 mm (2.7 inch)

Length - 213 mm (8.4 inch)

126-6611 Seal Driver

Caterpillar Information System:

1997/01/13 Spanner Wrenches And Related Tools To Remove And Install Final Drive Bearing Locknut{4050,0602}

1997/01/13 Use 125-4634 Spanner Wrench Assembly To Remove And Install 110-5425 Nut Retaining Axle Shaft Into Housing{3250,0727}

1997/01/13 1U-9058 Hose Group Provides All Necessary Equipment For Adjusting And Releasing Tension On Mobile-Trac Belts{4197,0766}

1997/01/13 1U-9054 Driver Lifter Removes And Installs Rear Drive Wheel Assembly Using Overhead Lifting Equipment{4199,0729}

1997/01/13 Use 1U-9097 Wrench To Remove And Install Accumulator In Mobile-Trac Tensioning System{4197,0756}

1997/01/13 1U-9055 Idler Lifter Removes And Installs Front Idler Assembly Using Overhead Lifting Equipment{4150,0729}

1997/01/13 1U-6130 Guide Stud, 1U-9785 Guide Stud And 1U-9817 Guide Stud Makes Undercarriage Installation And Removal Much Easier And More Efficient{4150,0729}

1997/01/13 1U-9095 Lifter Group Allows Complete Undercarriage To Be Moved With Fork Lift Or Farm Tractor{4150,0632}

1996/12/30 Flywheel Housing To Cylinder Block Joint Improvements {1157,1201}

1996/12/30 Improved Boom Electrical Harness Routing For Increased Reliability {1408}

1996/12/30 Supplement To Operation And Maintenance Manual; "Dual Position Switch To Operate The Tilt Kickout System" {1435,7451}

1996/12/30 Procedure For Aligning Front Suspension Frame Group With Output Transfer Gearbox {7200}

1997/01/13 129-7142 Lifting Beam Simplifies Removal And Installation Of Friction Group{6605,0632,0717}

1997/01/13 Fixture Assembly Allows More Accurate Levelling Of Screed Plates{6643,0764}

1997/01/13 More Collets Now Available For XT5 And XT6 Hoses Using 4C-9480 Hose Tooling Group{0684}

1997/01/13 Use 126-1023 Stem Pusher For Sleeve And Coupling Removal On Hose Assemblies{5057,0684}

1997/01/13 Piston Ring Groove Gauges To Quickly And Accurately Determine Reusability Of Pistons{1214,0763}

1997/01/13 Use 125-9622 Seal Installer To Install 118-9163 Seal In Water Pumps{1361,0708}

1997/01/13 Quickly And Accurately Set Valve Lash{1105,0766}

1997/01/20 Cab Rear Window Improvements Provide Improved Sealing And Visibility {7301,7310}

1997/01/20 Adjustment To Window Hold Back Latch Improves Operation {7301,7310}

1997/01/20 Special Edition, SEPD0325, "Major Improvements And Service Information For 768C, 772B, 776C, 776D Tractors, 771C, 771D, 775B, 775D Quarry Trucks And 769C, 769D, 773B, 773D, 777C And 777D Trucks" Is Available {0374}

1997/01/20 "E-Trim" Unit Fuel Injectors {1290}

1997/01/20 Modification Of Electronic Control Module (ECM) Controlled Variable Speed Fan Clutch Bracket-Shaft Assembly For Easier Fan Speed Sensor Removal {1359}