Usage:
CS-433C, CP-433C, CS-533C, CP-533C, CS-563C, CP-563C, CS-583C Vibratory Soil Compactors;
CB-534B, CB-534C, CB-634B, CB-634C Vibratory Asphalt Compactors
Reference: Service Manual, Disassembly and Assembly Module.
Warranty: G
Features/Benefits
-
- * Used to remove and install final drive bearing locknut when replacing bearings or Duo-Cone seals
- * Used with standard torque wrench to obtain up to 950 N·m (700 lb ft) of torque
- * Four spanner teeth provide positive engagement with locknut (virtually eliminates slippage and locknut damage)
- * Locknut cannot be properly installed using hammer and punch
- * Spanner wrenches are heat-treated for durability and long life
- * Used to remove and install final drive bearing locknut when replacing bearings or Duo-Cone seals
126-6608 Spanner Wrench:
-
- * Used on CS-433C, CP-433C Vibratory Soil Compactors; CB-534B, CB-534C, CB-634B and CB-634C Vibratory Asphalt Compactors
- * Designed to fit inside housing bore
- * Top of spanner wrench is designed to extend out beyond face of housing (allows use of torque wrench without need for an extension)
- * Used on CS-433C, CP-433C Vibratory Soil Compactors; CB-534B, CB-534C, CB-634B and CB-634C Vibratory Asphalt Compactors
126-6609 Spanner Wrench, 126-6610 Alignment Bracket, And 129-2343 Staking Tool:
-
- * Used on CS-533C, CP-533C, CS-563C, CP-563C and CS-583C Vibratory Soil Compactors
- * Spanner wrench is designed to fit down inside deep housing bore (locknut is over 90 mm (3.5 inch) down inside housing)
- * Designed to extend out beyond face of housing (round shank of spanner wrench extends beyond housing face and through alignment bracket)
- * 126-6610 Alignment Bracket bolts directly onto housing and provides a reaction point for torque wrench (permits one-person tightening of locknut)
- * Bracket uses existing final drive holes and bolts for mounting
- * 129-2343 Staking Tool provides best method of properly securing locknut onto shaft (simple and easy to use; refer to Illustration 4)
- * Staking tool locates point of punch in the correct position to peen or stake locknut onto shaft (a regular punch could slip off of locknut and cause bearing damage)
- * Used on CS-533C, CP-533C, CS-563C, CP-563C and CS-583C Vibratory Soil Compactors
Specifications/Technical Information
- Working torque capacity of spanner wrenches - 950 N·m (700 lb ft)
- Square drive - 3/4 inch
126-6608 Spanner Wrench:
- Width of square teeth - 14.3 mm (.56 inch)
- Distance between teeth - 214 mm (8.4 inch)
126-6609 Spanner Wrench:
- Width of square teeth - 14.3 mm (.56 inch)
- Distance between teeth - 232 mm (9.2 inch)
Illustration 1. 126-6608 Spanner Wrench
Illustration 2.
(1) 126-6609 Spanner Wrench. (2) 126-6610 Alignment Bracket. (3) 129-2343 Staking Tool.
Illustration 3.
Using the 126-6609 Spanner Wrench (1) and 126-6610 Alignment Bracket (2) to Install Locknut.
Illustration 4.
Using the 129-2343 Staking Tool (3) to lock the locknut in place.