Crankshaft Rear Seal - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 5B-4274 | Bolt | 3 |
B | 8T-0914(1) | Guide Pin | 2 |
C | - | Guide Studs 3/8 - 16 by 5 inch |
2 |
D | 1P-0808 | Multipurpose Grease | - |
Show/hide table
(1) | Part of 9U-5105 Engine Tool Group |
Start By:
- Remove the flywheel.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (2) that hold the crankshaft rear seal and adapter (1) in place.
- Install Tooling (A) in adapter (1). Tighten Tooling (A) evenly. Remove the crankshaft rear seal and adapter (1) from the flywheel housing.
- Install Tooling (B) through the holes in adapter (4).
- Remove bolts (3) that hold adapter (4) in place.
- Slide adapter (4) onto Tooling (B). Attach a suitable lifting device to adapter (4). The weight of adapter (4) is approximately
65 kg (143 lb) . Remove adapter (4) from Tooling (B).
Show/hide table
Illustration 1 | g01294474 |
Note: It is not necessary to remove adapter (4) in order to remove the crankshaft rear seal.
- Install Tooling (B) in the rear of the crankshaft.
Note: The dash marks on the sleeve in adapter (4) must be aligned with the dash mark on the crankshaft.
- Attach a suitable lifting device to adapter (4). The weight of adapter (4) is approximately
65 kg (143 lb) . Place adapter (4) in position on Tooling (B). Install bolts (3) that hold adapter (4) in place. - Remove Tooling (B).
Note: The crankshaft rear seal must be installed with the lip of the seal toward the inside of the engine. Ensure that the correct seal is installed on each end of the crankshaft.
- Install Tooling (C) in the flywheel housing.
- Apply Tooling (D) to the O-ring seal on the outside diameter of adapter (1).
Note: Ensure that all the parts are clean. Do not touch the lip of the seal. Do not use lubricant on the lip of the seal. Ensure that the arrow on the seal points in the same direction as the crankshaft rotation.
- Place the crankshaft rear seal and adapter (1) on Tooling (C). Carefully slide the crankshaft rear seal and adapter (1) on the flywheel housing.
- Install bolts (2) that hold the crankshaft rear seal and adapter (1) in place.
Show/hide table
Illustration 2 | g01294474 |
End By:
- Install the flywheel.
Caterpillar Information System:
C280-08 Tier 4 Engine Crankshaft Front Seal - Remove and Install
C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225} C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225}
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Flywheel and Ring Gear - Remove and Install
C15 and C18 Tier 4 Final Engines Aftertreatment SCR System Dosing - Test
Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N} Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N}
C280-08 Tier 4 Engine Vibration Damper - Remove and Install
C280-08 Tier 4 Engine Priority Valve - Assemble
C280-08 Tier 4 Engine Priority Valve - Disassemble
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Priority Valve - Remove and Install
C280-08 Tier 4 Engine Oil Temperature Regulators - Remove and Install
C280-08 Tier 4 Engine Engine Oil Pan - Assemble
C280-08 Tier 4 Engine Engine Oil Pan - Disassemble
C280-08 Tier 4 Engine Crankshaft Front Gear - Remove and Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Crankshaft Rear Gear - Remove and Install
C280-08 Tier 4 Engine Camshaft Drive Gear - Remove
C280-08 Tier 4 Engine Camshaft Drive Gear - Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Idler Gears (Rear) - Remove
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Idler Gears (Rear) - Install
C280-08 Tier 4 Engine Idler Gears (Front) - Remove
C280-08 Tier 4 Engine Idler Gears (Front) - Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Housing (Front) - Remove and Install
G3600 A4 Engines Connecting Rod Bearings - Inspect
Well Stimulation Pumps Maintenance Interval Schedule
3516C Marine Engine Maintenance Recommendations