Idler Gears (Front) - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 5B-4274 | Bolt | 2 |
Start By:
- Remove the water pumps.
- Remove the engine oil pump.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove the bolts that hold idler shaft (2) in place.
Note: DO NOT allow the gear to fall when the idler shaft is removed.
- Install Tooling (A) in idler shaft (2).
- Support idler gear (1). Tighten Tooling (A) evenly. Remove idler shaft (2) from the front housing.
- Remove idler gear (1) from the front housing.
Show/hide table
Illustration 2 g00561404 - Remove O-ring seals (3) from idler shaft (2).
Show/hide table
Illustration 3 g00561405 Note: The idler bearing in the illustration shows a groove for an internal oil supply. The new idler bearings do not have a groove for an internal oil supply.
- If necessary, remove bearing (4) from idler gear (1).
Show/hide table
Illustration 4 g03743336 - Remove thrust washer (5) from the front housing.
Show/hide table
Illustration 1 | g03743334 |
Note: The same procedure is used for removing the idler gears and the idler shafts on both sides. The idler gears on each side are different. The idler gears must be installed on the correct side in order to get the correct engagement with the crankshaft gear.
Caterpillar Information System:
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Idler Gears (Rear) - Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Idler Gears (Rear) - Remove
C280-08 Tier 4 Engine Camshaft Drive Gear - Install
C280-08 Tier 4 Engine Camshaft Drive Gear - Remove
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Crankshaft Rear Gear - Remove and Install
C280-08 Tier 4 Engine Crankshaft Front Gear - Remove and Install
C280-08 Tier 4 Engine Crankshaft Rear Seal - Remove and Install
C280-08 Tier 4 Engine Crankshaft Front Seal - Remove and Install
C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225} C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225}
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Flywheel and Ring Gear - Remove and Install
C15 and C18 Tier 4 Final Engines Aftertreatment SCR System Dosing - Test
Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N} Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N}
C280-08 Tier 4 Engine Idler Gears (Front) - Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Housing (Front) - Remove and Install
G3600 A4 Engines Connecting Rod Bearings - Inspect
Well Stimulation Pumps Maintenance Interval Schedule
3516C Marine Engine Maintenance Recommendations
140 Motor Graders Air Cleaner
140 Motor Graders Air Lines
C4.4 Marine Generator Set Cylinder Is Noisy
C4.4 Marine Generator Set ECM Does Not Communicate with Other Modules
C4.4 Marine Generator Set ECM Will Not Accept Factory Passwords
C4.4 Marine Generator Set Electronic Service Tool Does Not Communicate
DRCP Connector Repair Service Instruction {1408, 7553} DRCP Connector Repair Service Instruction {1408, 7553}