Crankshaft Front Gear - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 8T-0914(1) | Guide Pin | 2 |
B | 183-3424 | Grease Cartridge | - |
Show/hide table
(1) | Part of 9U-5105 Engine Tool Group |
Start By:
- Remove the crankshaft front seal.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install Tooling (A) in the crankshaft.
- Attach a suitable lifting device to crankshaft front gear (1). The weight of crankshaft front gear (1) is approximately
34 kg (75 lb) . Slide crankshaft front gear (1) onto Tooling (A). Remove crankshaft front gear (1). - Remove the O-ring seals from each side of crankshaft front gear (1). Discard the O-ring seals.
Show/hide table
Illustration 1 | g03743318 |
- Install Tooling (A) in the crankshaft.
- Lubricate the bores of the new O-ring seals with clean engine oil. Install the O-ring seals in crankshaft front gear (1). Apply Tooling (B) to the bore of the crankshaft front gear. Attach a suitable lifting device to crankshaft front gear (1). The weight of crankshaft front gear (1) is approximately
34 kg (75 lb) .Note: If holes (2) in the crankshaft will not align with the holes in the crankshaft front gear, the wrong side of the crankshaft front gear is toward the crankshaft.
- Align holes (2) in the crankshaft with the holes in the crankshaft front gear. Install crankshaft front gear (1) on Tooling (A).
- Slide crankshaft front gear (1) against the crankshaft.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Illustration 2 | g03743318 |
Show/hide table
Illustration 3 | g00559762 |
End By:
- Install the crankshaft front seal.
Caterpillar Information System:
C280-08 Tier 4 Engine Crankshaft Rear Seal - Remove and Install
C280-08 Tier 4 Engine Crankshaft Front Seal - Remove and Install
C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225} C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225}
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Flywheel and Ring Gear - Remove and Install
C15 and C18 Tier 4 Final Engines Aftertreatment SCR System Dosing - Test
Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N} Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N}
C280-08 Tier 4 Engine Vibration Damper - Remove and Install
C280-08 Tier 4 Engine Priority Valve - Assemble
C280-08 Tier 4 Engine Priority Valve - Disassemble
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Priority Valve - Remove and Install
C280-08 Tier 4 Engine Oil Temperature Regulators - Remove and Install
C280-08 Tier 4 Engine Engine Oil Pan - Assemble
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Crankshaft Rear Gear - Remove and Install
C280-08 Tier 4 Engine Camshaft Drive Gear - Remove
C280-08 Tier 4 Engine Camshaft Drive Gear - Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Idler Gears (Rear) - Remove
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Idler Gears (Rear) - Install
C280-08 Tier 4 Engine Idler Gears (Front) - Remove
C280-08 Tier 4 Engine Idler Gears (Front) - Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Housing (Front) - Remove and Install
G3600 A4 Engines Connecting Rod Bearings - Inspect
Well Stimulation Pumps Maintenance Interval Schedule
3516C Marine Engine Maintenance Recommendations
140 Motor Graders Air Cleaner