Priority Valve - Assemble
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean all parts. Replace all parts that are damaged.
Show/hide table
Illustration 1 g00556060 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Apply clean engine oil to all parts of the valve before assembly.
- Install piston (6) in body (5). Install the piston with the shorter end of the piston toward the inside of the body. The piston must move freely inside the body.
- Install spring (7) and piston (2) in piston (6). Piston (2) must move freely in piston (6).
- Install piston (8) and spring (9) in body (5).
- Install O-ring seal (1) in body (5).
Note: Ensure that spring (9) fits into the counterbore in cover (3) when the cover is installed.
- Place cover (3) in position on body (5). Install bolts (4).
End By:
- Install the priority valve.
Caterpillar Information System:
C280-08 Tier 4 Engine Priority Valve - Disassemble
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Priority Valve - Remove and Install
C280-08 Tier 4 Engine Oil Temperature Regulators - Remove and Install
C280-08 Tier 4 Engine Engine Oil Pan - Assemble
C280-08 Tier 4 Engine Engine Oil Pan - Disassemble
C280-08 Tier 4 Engine Engine Oil Pan - Remove and Install
374F and 390F Excavators Tool Control System One-Way/Two Pump - Electric Control: Relief Valve (Line) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Main) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Line) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Default Value of Work Tool Parameters
C4.4 Marine Generator Set Crankcase Fumes Disposal Tube Has Oil Draining
C4.4 Marine Generator Set Crankcase Breather Ejects Oil
C280-08 Tier 4 Engine Vibration Damper - Remove and Install
Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N} Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N}
C15 and C18 Tier 4 Final Engines Aftertreatment SCR System Dosing - Test
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Flywheel and Ring Gear - Remove and Install
C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225} C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225}
C280-08 Tier 4 Engine Crankshaft Front Seal - Remove and Install
C280-08 Tier 4 Engine Crankshaft Rear Seal - Remove and Install
C280-08 Tier 4 Engine Crankshaft Front Gear - Remove and Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Crankshaft Rear Gear - Remove and Install
C280-08 Tier 4 Engine Camshaft Drive Gear - Remove
C280-08 Tier 4 Engine Camshaft Drive Gear - Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Idler Gears (Rear) - Remove