Priority Valve - Remove and Install
Show/hide table
 |
|
Do not remove the priority valve while the engine is hot. Hot oil can cause burns. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Allow the engine to cool after shutdown. Allow the volume of engine oil above the priority valve, the engine oil filters, and the engine oil cooler to drain to the engine oil pan.
Show/hide table
Illustration 1 g03744417 - Disconnect harness assembly (1). Remove elbow (2). Remove the O-ring seals (not shown).
Show/hide table
Illustration 2 g03744419 - Remove elbow (3). Remove bracket (4).
Show/hide table
Illustration 3 g03744421 - Remove bolts (5) and priority valve (6).
Show/hide table
Illustration 4 g03744424 - Remove O-ring seals (7) from the front housing.
- Install priority valve (6) in the reverse order of removal.
- Ensure that the engine is filled with oil to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil - Change" for the correct filling procedure.
Caterpillar Information System:
C280-08 Tier 4 Engine Oil Temperature Regulators - Remove and Install
C280-08 Tier 4 Engine Engine Oil Pan - Assemble
C280-08 Tier 4 Engine Engine Oil Pan - Disassemble
C280-08 Tier 4 Engine Engine Oil Pan - Remove and Install
374F and 390F Excavators Tool Control System One-Way/Two Pump - Electric Control: Relief Valve (Line) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Main) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Line) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Default Value of Work Tool Parameters
C4.4 Marine Generator Set Crankcase Fumes Disposal Tube Has Oil Draining
C4.4 Marine Generator Set Crankcase Breather Ejects Oil
C4.4 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C4.4 Marine Generator Set Coolant Temperature Is High
C280-08 Tier 4 Engine Priority Valve - Disassemble
C280-08 Tier 4 Engine Priority Valve - Assemble
C280-08 Tier 4 Engine Vibration Damper - Remove and Install
Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N} Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N}
C15 and C18 Tier 4 Final Engines Aftertreatment SCR System Dosing - Test
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Flywheel and Ring Gear - Remove and Install
C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225} C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225}
C280-08 Tier 4 Engine Crankshaft Front Seal - Remove and Install
C280-08 Tier 4 Engine Crankshaft Rear Seal - Remove and Install
C280-08 Tier 4 Engine Crankshaft Front Gear - Remove and Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Crankshaft Rear Gear - Remove and Install
C280-08 Tier 4 Engine Camshaft Drive Gear - Remove