Engine Oil Pan - Assemble
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A(1) | 5P-5247 | Hydraulic Puller | 1 |
| 1U-5230 | Hand Hydraulic Pump | 1 | |
| 8T-0820 | Hydraulic Pressure Gauge | 1 | |
| 3S-6224 | Electric Hydraulic Pump | 1 | |
| 8S-8033 | Electric Hydraulic Pump | 1 | |
| 9U-6600 | Hand Hydraulic Pump | 1 | |
| 8T-3035 | Hydraulic Line | 1 | |
Show/hide table
| (1) | Four pumps are listed as Tooling (A). Only one of the pumps is needed to assemble the engine oil pan. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install O-ring seal (13) on housing (5). Apply glycerin to the O-ring seal.
Show/hide table
Illustration 2 g01293463 - Use Tooling (A) and a steel plate in order to install housing (5) into engine oil pan (14). Use a block of wood between the hydraulic puller and the bulkhead of the engine oil pan.
Show/hide table
Illustration 3 g00632999 Show/hide table
Illustration 4 g01293490 - Install a new O-ring seal on tube assembly (4). Apply glycerin to the O-ring seal.
- Use Tooling (A) in order to install tube assembly (4) into housing (5).
- Install a new O-ring seal (15) on tube assembly (4). Apply glycerin to the O-ring seal.
Show/hide table
Illustration 5 g01293492 - Install suction bell (2) onto tube assembly (4).
Show/hide table
NOTICE Do not attempt to close the gap between the suction bell and the bulkhead by tightening the bolts. Breakage to the aluminum parts can occur.
- If necessary, install spacers (16) in order to fill the gap between the mounting brackets on the suction bell and the bulkhead. If necessary, move the suction bell away from tube assembly (4). Move the suction bell enough in order to obtain clearance for spacers (16). Do not move the suction bell more than this amount.
Show/hide table
Illustration 6 g01293473 - Install bolts (17) and the washers.
- Install clamp (3).
Show/hide table
Illustration 7 g00632989 - Install screen (1) into the housing. Make sure that the screen is engaged with the slots in the housing.
Show/hide table
| |
| Illustration 1 | g01293461 |
- Install the O-ring seal on tube assembly (12). Install tube assembly (12) and clamp (11).
Show/hide table
Illustration 9 g01293432 - Install suction bell (10).
Show/hide table
Illustration 10 g01293429 - If tee (7) was removed, install tee (7) with bolts (9). Install the suction screen into the tube assembly. Install cover (8) and install bolts (6).
Show/hide table
| |
| Illustration 8 | g01293434 |
End By:
- Install the engine oil pan.
Caterpillar Information System:
C280-08 Tier 4 Engine Engine Oil Pan - Disassemble
C280-08 Tier 4 Engine Engine Oil Pan - Remove and Install
374F and 390F Excavators Tool Control System One-Way/Two Pump - Electric Control: Relief Valve (Line) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Main) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Relief Valve (Line) - Test and Adjust
374F and 390F Excavators Tool Control System Medium Pressure: Default Value of Work Tool Parameters
C4.4 Marine Generator Set Crankcase Fumes Disposal Tube Has Oil Draining
C4.4 Marine Generator Set Crankcase Breather Ejects Oil
C4.4 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C4.4 Marine Generator Set Coolant Temperature Is High
C4.4 Marine Generator Set Coolant Level Is Low
C4.4 Marine Generator Set Coolant Contains Oil
C280-08 Tier 4 Engine Oil Temperature Regulators - Remove and Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Priority Valve - Remove and Install
C280-08 Tier 4 Engine Priority Valve - Disassemble
C280-08 Tier 4 Engine Priority Valve - Assemble
C280-08 Tier 4 Engine Vibration Damper - Remove and Install
Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N} Updating the NOx Reduction System Delta Pressure Sensor on Certain C9.3 Through C32 Engines {1408, 191N}
C15 and C18 Tier 4 Final Engines Aftertreatment SCR System Dosing - Test
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Flywheel and Ring Gear - Remove and Install
C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225} C-16 and 3456Cylinder Packs, Short Blocks, and Long Blocks May Have Oversize Piston Skirts{1225}
C280-08 Tier 4 Engine Crankshaft Front Seal - Remove and Install
C280-08 Tier 4 Engine Crankshaft Rear Seal - Remove and Install
C280-08 Tier 4 Engine Crankshaft Front Gear - Remove and Install