Final Drive - Disassemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P - 2420 | Repair Stand | 1 |
B | 1U - 6400 | Puller | 1 |
C | 5P - 8707 | Plate | 1 |
1P - 0520 | Driver Group | 1 | |
5F - 7366 | Forcing Bolt | 1 | |
8T - 0207 | Bolt | 2 | |
3H - 0465 | Puller Plate | 2 | |
1P - 5546 | Cross Block | 1 |
Start By:
- Remove the final drive.
- Secure final drive (3) to Tooling (A) The weight of the final drive is approximately
254 kg (560 lb) . Remove bolts (2) and housing (1). Remove O-ring seal from housing (1).Show/hide tableIllustration 2 g03034527 Show/hide tableIllustration 3 g03034528 - Remove retaining ring (4) and planet gear (5). If necessary, use Tooling (B) to remove planet gears (5).
Show/hide table
Illustration 4 g03034530 - Remove retaining ring (7) and planet gear carrier (6).
Show/hide table
Illustration 5 g03034536 - Remove sun gear (8).
Show/hide table
Illustration 6 g03034556 - Remove spacer (9) from sun gear (8).
Show/hide table
Illustration 7 g03034559 Show/hide tableIllustration 8 g03034582 - Remove sun gear (12) and remove retaining ring (10) and planet gears (11). If necessary, use Tooling (B) to remove planet gears (11).
Show/hide table
Illustration 9 g03034575 - Remove retaining ring (13) and planet carrier (14).
Show/hide table
Illustration 10 g03034581 - Remove sun gear (16) and remove bolt's (15).
Show/hide table
Illustration 11 g03034598 - Attach suitable lifting device to planet carrier (17). The weight of plant carrier is approximately
32 kg (70 lb) . Remove planet carrier (17).Show/hide tableIllustration 12 g03034599 - Remove final drive (3) from Tooling (A). Place final drive (3) on floor. The weight of final drive is approximately
163 kg (360 lb) .Remove bolts (18) and flange (19).Show/hide tableIllustration 13 g03034600 - Use Tooling (C) to press down on the pushing disc (20), to remove retaining ring (21).
Show/hide table
Illustration 14 g03034604 - Remove springs (22) and brake shaft (23).
Show/hide table
Illustration 15 g03034620 - Remove piston (24).
Show/hide table
Illustration 16 g03034621 - Remove plates (25) and discs (26) .
Note: Note the order at which the friction discs and plates are removed. For installation purposes.
Show/hide tableIllustration 17 g03034698 - Remove O-ring seals (27), cap screws (28) and cover (29).
Show/hide table
Illustration 18 g03034716 Show/hide tableIllustration 19 g03034718 - Remove Duo-Cone seal (30) and Duo-Cone seal (31).
Show/hide table
Illustration 1 | g03034523 |
Caterpillar Information System:
320 VH and VM Variable Gauge Undercarriage Final Drive - Assemble
2012/07/23 Improved Hose Assemblies Are Now Used on Certain C27 and C32 Petroleum Engines {1307, 1308}
C13-XQ350 Rental Generator Set Starting the Engine
C32 Marine Engines Fuel Temperature Sensor - Remove and Install
C13, C15, and C18 Tier 4 Final Engines SCR Warning System Problem
TH48-E80 Petroleum Transmission Selector and Pressure Control Valve (Transmission)
C9.3 Tier 4 Final Engines Power Is Intermittently Low or Power Cutout Is Intermittent
C32 Marine Engines Fuel Pressure Sensor - Remove and Install
C9.3 Tier 4 Final Engines Oil Contains Fuel
C9.3 Tier 4 Final Engines Fuel Temperature Is High
C13, C15, and C18 Tier 4 Final Engines Fuel Pressure Is Low
C9.3 Tier 4 Final Engines Fuel Pressure Is High
C9.3 Tier 4 Final Engines Speed/Timing - Test
2013/03/12 Bearing Service Interval Is Extended for Certain Uninterruptible Power Supplies {4480, 7551}
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Maintenance Interval Schedule
C32 Marine Engines Speed/Timing Sensor - Remove and Install
C13-XQ350 Rental Generator Set Product Description
C7.1 Industrial Engine Introduction
C7.1 Industrial Engine Clean Emissions Module
C7.1 Industrial Engine DEF Dosing Control System
Investigation of Fault or Dropped Load on UPSB125/130 Systems{4480} Investigation of Fault or Dropped Load on UPSB125/130 Systems{4480}
2012/05/16 New Oil Level Gauges Are Used on Certain C7 Commercial Engines {1326}
C32 Marine Engines Inlet Air Temperature Sensor - Remove and Install
C32 Marine Engines Alternator - Remove and Install