Fuel Lines - Remove and Install
拆卸步骤
Show/hide table
接触高压燃油可能导致液体渗透和烧伤危险。 高压燃油溢出可能会产生火灾。 如果不遵循检查、保养和维修指南,可能会造成人身伤亡。 |
Show/hide table
注意 |
---|
触及高压燃油可能导致人身伤害或死亡。在对发动机燃油管进行任何维修或修理前,应在关闭发动机后等待 60 秒钟,以释放压力。 |
Show/hide table
注意 |
---|
在检查, 保养, 测试, 调整 和 维修发动机时,务必留心,确保将溢出的液体盛装在容器中。在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
Show/hide table
注意 |
---|
清洁度是一项重要的因素。 在执行拆卸步骤之前,请清洁部件的外部。 确保彻底清洁了燃油歧管和燃油管周围的区域。 此操作有助于防止污染物进入内部机构。 在更换任何燃油管之前,请遵循下面列出的说明。 用正确的燃油管总成更换燃油管。 |
注: 以下步骤用于完成所有燃油管和卡箍的拆卸。 如果只需要更换特定的燃油管,则只更换需要更换的燃油管和卡箍。
- 将燃油供应转到断开位置。
- 断开蓄电池。 请参阅操作和保养手册, "蓄电池或蓄电池电缆 - 断开"。
- 拆下所有部件以接近导线线束。
- 松开卡箍组件 (1) ,然后拆下软管 (2) 。
Show/hide table
图 1 | g02140798 |
- 断开接头 (3) 和 (7) 。
Show/hide table
图 2 | g02140852 |
- 拆下螺栓 (5) 、 (6) 和 (8) ,然后拆下管组件 (4) 。
- 拆下螺栓 (9) 。
- 拆下螺母 (10) ,然后拆下支架 (11) 。
Show/hide table
图 3 | g02140971 |
- 断开线束组件 (12) 。
- 将线束组件 (13) 移开。 从双头螺栓 (14) 上拆下隔套。
Show/hide table
图 4 | g02141119 |
- 拆下螺栓 (15) ,然后拆下卡箍组件。 废弃卡箍组件。
Show/hide table
图 5 | g02141131 |
- 拆下螺母 (23) 、 (19) 和 (20) 。 拆下相应的卡箍组件并将其废弃。
- 松开螺母 (16) 和 (18) 。 拆下并废弃燃油管 (17) 。 对其余的燃油管重复上述步骤。
- 松开螺母 (21) 和 (24) 。 拆下并废弃燃油管 (22) 。
安装步骤
Show/hide table
注意 |
---|
喷油管仅能使用一次。使用后弃置所有喷油管。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 请确保直至燃油管被放置到相应的端口附近时燃油管盖都保持在位,以防止发生污染。 在继续执行本步骤之前,请确保彻底清洁了导轨和燃油管周围的区域。 如果任何零件磨损或损坏,则应使用新零件进行更换。 清洁度是一项重要的因素。 确保在安装过程中不会有任何碎屑进入燃油系统。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 安装新燃油管 (17) 。 手动拧紧燃油管每一端上的螺母 (16) 和 (18) 。 对其余的燃油管重复上述步骤。
Show/hide table
图 6 | g02141131 |
Show/hide table
图 7 | g02141119 |
注: 请确保直至燃油管被放置到相应的端口附近时燃油管盖都保持在位,以防止发生污染。
- 安装新燃油管 (22) 。 手动拧紧螺母 (21) 和 (24) 。
- 放置线束组件并安装螺栓 (15) 。 手动拧紧螺栓。未能将护孔环正确放置燃油管上会导致燃油管故障。
- 放置卡箍组件并安装螺母 (23) 、 (19) 和 (20) 。 手动拧紧螺母。 未能将护孔环正确放置燃油管上会导致燃油管故障。
- 将燃油导轨处的螺母 (24) 和 (18) 拧紧至扭矩为 27 ± 3 N·m (239 ± 27 lb in)。
注: 在拧紧之前,请确保燃油管处于螺母的中央。 组装燃油管时,请勿使用过多的力或进行弯曲。
- 将螺母 (21) 和 (16) 拧紧至扭矩为 27 ± 3 N·m (239 ± 27 lb in)。
- 将螺栓 (15) 、螺母 (23) 、 (19) 和 (20) 拧紧至扭矩为 12 ± 3 N·m (105 ± 27 lb in)。
- 将隔套(未显示)和线束 (13) 放置到双头螺栓 (14) 上。
- 安装支架 (11) ,然后安装螺母 (10) 。
Show/hide table
图 8 | g02140971 |
- 连接线束组件 (12) 。
- 放置管组件 (4) 。 连接接头 (3) 和 (7) 。 安装螺栓 (5) 、 (6) 和 (8) 。
Show/hide table
图 9 | g02140852 |
- 安装螺栓 (9) 。
- 放置软管组件 (2) ,然后安装卡箍组件 (1) 。
Show/hide table
图 10 | g02140798 |
- 连接蓄电池。 请参阅操作和保养手册, "蓄电池或蓄电池电缆 - 连接"。
- 将燃油供应转到接通位置。
Caterpillar Information System:
G3304B and G3306B Engines Carburetor - Remove
C11 and C13 Engines Engine Oil Pump
C18 Marine Engine Plate Locations and Film Locations
G3304B and G3306B Engines Gas Pressure Regulator - Install
C13 Engine for Combat and Tactical Vehicles Air Lines
C11 and C13 Engines Cylinder Head Valves
G3304B and G3306B Engines Gas Pressure Regulator - Assemble
G3304B and G3306B Engines Gas Pressure Regulator - Disassemble
G3304B and G3306B Engines Starting Air Pressure - Adjust
G3304B and G3306B Engines Air Starting Motor - Lubricate
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Replaced Relay or Solenoid Does Not Operate
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Transmission Does Not Automatically Shift Back Into Gear
2009/06/01 Guidelines for Reusability of Cylinder Head Studs, Main Bearing Cap Studs, Main Bearing Cap Cross Tie Bolts, and Connecting Rod Cap Bolts and Nuts {1100, 1218, 1230}
G3304B and G3306B Engines Spark Plug - Test
Procedure to Rerate the Engine with Caterpillar Electronic Technician (ET) {1901, 1902, 1920} Procedure to Rerate the Engine with Caterpillar Electronic Technician (ET) {1901, 1902, 1920}
Failures of Cylinder Heads with the Intake Valves and Exhaust Valves in the Incorrect Positions{1100, 1105} Failures of Cylinder Heads with the Intake Valves and Exhaust Valves in the Incorrect Positions{1100, 1105}
C11, C13 and C15 On-highway Engines 0173-00 High Exhaust Gas Temperature Derate
2009/06/08 A Hotline for the Fuel Systems for Hydraulic Electronic Unit Injectors (HEUI) Is Now Available. {1251, 1290}
2009/06/01 A Hotline for the Fuel Systems for Hydraulic Electronic Unit Injectors (HEUI) Is Now Available. {1251, 1290}
3516B Engine for 994F and 994H Wheel Loaders Power Is Intermittently Low or Power Cutout Is Intermittent
C18 Marine Generator Set Model View Illustrations
C7.1 Industrial Engine and Generator Set 5 Volt Sensor Supply Circuit - Test
G3304B and G3306B Engines Indicator Lamp - Test
C13 Engine for Caterpillar Built Machines Belt Tensioner - Remove and Install