Cylinder Head Valves
Show/hide table
Illustration 1 | g01351852 |
Show/hide table
Illustration 2 | g02745479 |
Inlet valve |
Note: Apply 8T-9548 Oil to the valve stems prior to installation in the cylinder head.
(1) Inlet valve
- (B) Valve stem diameter ...
9.441 ± 0.008 mm (0.3717 ± 0.0003 inch) - (C) Diameter of valve head ...
44.50 ± 0.13 mm (1.752 ± 0.005 inch) - (D) Valve face angle ... 60.75 ± 0.25 degrees
- (E) Minimum valve stem diameter ...
9.309 mm (0.3665 inch) - (F) Width of the valve head ...
3.5 ± 0.2 mm (0.14 ± 0.01 inch) - (C) Diameter of valve head ...
Show/hide table
Illustration 3 | g02746141 |
Exhaust valve |
(2) Exhaust valve
- (G) Valve stem diameter ...
9.441 ± 0.008 mm (0.3717 ± 0.0003 inch) - (H) Diameter of valve head ...
41.50 ± 0.13 mm (1.634 ± 0.005 inch) - (J) Valve face angle ... 45.75 ± 0.25 degrees
- (K) Minimum valve stem diameter ...
9.309 mm (0.3665 inch) - (L) Width of the valve head ...
3.25 ± 0.10 mm (0.128 ± 0.004 inch) - (H) Diameter of valve head ...
(3) 224-4441 Spring
- Assembled length ...
50.47 mm (1.987 inch) - Load at assembled length ...
160 ± 13 N (36 ± 3 lb) - Minimum operating length ...
34.92 mm (1.375 inch) - Load at minimum operating length ...
385 ± 18 N (87 ± 4 lb) - Outside diameter ...
23.24 mm (0.915 inch) - Free length after test ...
64.1 mm (2.52 inch) - Load at assembled length ...
Inner valve spring
(4) 332-2152 Spring
- Assembled length ...
52.95 mm (2.085 inch) - Load at assembled length ...
320 ± 31 N (72 ± 7 lb) - Minimum operating length ...
37.40 mm (1.472 inch) - Load at minimum operating length ...
860 ± 34 N (193 ± 8 lb) - Outside diameter ...
34 mm (1.3 inch) - Free length after test ...
62.7 mm (2.47 inch) - Load at assembled length ...
Outer valve spring
Note: Apply clean 8T-9548 Oil to the valve guide bore before installing the valve guides.
(5) Valve guides
- Bore of installed valve guide ...
9.508 ± 0.013 mm (0.3743 ± 0.0005 inch) - Maximum recommended diameter of the valve guide bore ...
9.544 mm (0.3760 inch) - (A) Height to the step in the valve guide ...
22 ± 0.5 mm (0.87 ± 0.012 inch) - Maximum recommended diameter of the valve guide bore ...
Note: Do not use a combination of a valve and a valve guide that has a difference of
(6) Inlet valve seat
- Angle of valve seat ... 29.75 ± 0.25 degrees
- Diameter of valve seat ...
45.525 ± 0.013 mm (1.7923 ± 0.0005 inch) - Bore in cylinder head for valve seat ...
45.460 ± 0.015 mm (1.7898 ± 0.0006 inch) - Diameter of valve seat ...
(7) Exhaust valve seat
- Angle of valve seat ... 44.75 ± 0.25 degrees
- Diameter of valve seat ...
42.390 ± 0.015 mm (1.6690 ± 0.0006 inch) - Bore in cylinder head for valve seat ...
42.320 ± 0.015 mm (1.6661 ± 0.0006 inch) - Diameter of valve seat ...
Caterpillar Information System:
G3304B and G3306B Engines Gas Pressure Regulator - Assemble
G3304B and G3306B Engines Gas Pressure Regulator - Disassemble
G3304B and G3306B Engines Starting Air Pressure - Adjust
G3304B and G3306B Engines Air Starting Motor - Lubricate
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Replaced Relay or Solenoid Does Not Operate
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Transmission Does Not Automatically Shift Back Into Gear
G3304B and G3306B Engines Unburned Gas - Purge
G3304B and G3306B Engines Gas Pressure Regulator - Remove
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Transmission Does Not Automatically Shift Into Neutral
C9.3 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
G3304B and G3306B Engines Engine Support - Remove and Install
2009/06/08 Improved Hardware Is Used on the Sealing Joint between the Turbocharger and the Exhaust Manifold on Certain 3512B Marine Engines {1052, 1053}
C13 Engine for Combat and Tactical Vehicles Air Lines
G3304B and G3306B Engines Gas Pressure Regulator - Install
C18 Marine Engine Plate Locations and Film Locations
C11 and C13 Engines Engine Oil Pump
G3304B and G3306B Engines Carburetor - Remove
C9.3 Engines for Caterpillar Built Machines Fuel Lines - Remove and Install
2009/06/01 Guidelines for Reusability of Cylinder Head Studs, Main Bearing Cap Studs, Main Bearing Cap Cross Tie Bolts, and Connecting Rod Cap Bolts and Nuts {1100, 1218, 1230}
G3304B and G3306B Engines Spark Plug - Test
Procedure to Rerate the Engine with Caterpillar Electronic Technician (ET) {1901, 1902, 1920} Procedure to Rerate the Engine with Caterpillar Electronic Technician (ET) {1901, 1902, 1920}
Failures of Cylinder Heads with the Intake Valves and Exhaust Valves in the Incorrect Positions{1100, 1105} Failures of Cylinder Heads with the Intake Valves and Exhaust Valves in the Incorrect Positions{1100, 1105}
C11, C13 and C15 On-highway Engines 0173-00 High Exhaust Gas Temperature Derate
2009/06/08 A Hotline for the Fuel Systems for Hydraulic Electronic Unit Injectors (HEUI) Is Now Available. {1251, 1290}