Starting Air Pressure - Adjust
必须检查每台发动机的安装,以确定最有利的起动条件。 气压调节阀的设定受到下述因素的影响:
- 来自起动期间发动机拖动的附加装置的负载
- 环境温度条件
- 空气起动马达润滑剂的粘度
- 储气罐的容量
- 发动机状况
较高的气压增加起动马达的扭矩和使发动机更快地旋转。 较低的气压延长压缩空气的供气时间。
注: 确保供气管具有适当的尺寸。 如未能提供足够量的空气到起动机,则将会导致起动机旋转减慢和起动扭矩降低。
使用下述步骤来检查和调整气压调节阀:
- 将压缩空气从系统中排出。
- 断开调节器出气口 (3) 的气管。
Show/hide table
图 1 | g00281476 |
压力调节阀 (1) 调节螺钉 (2) 调节器进气口 (3) 调节器出气口 |
- 将 8T-0849 压力表 连接到调节器出气口 (3) 。
- 向压力表施加气压,并检查气压。
- 使用调整螺钉 (1) 将气压调整到 620 至 1030 kPa (90 至 150 psi)。
- 正确调整气压之后,将系统的压缩空气排出。
- 从调节器出气口拆下 8T-0849 压力表总成 。 接回气管。
Caterpillar Information System:
G3304B and G3306B Engines Air Starting Motor - Lubricate
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Replaced Relay or Solenoid Does Not Operate
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Transmission Does Not Automatically Shift Back Into Gear
G3304B and G3306B Engines Unburned Gas - Purge
G3304B and G3306B Engines Gas Pressure Regulator - Remove
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Transmission Does Not Automatically Shift Into Neutral
C9.3 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
G3304B and G3306B Engines Engine Support - Remove and Install
2009/06/08 Improved Hardware Is Used on the Sealing Joint between the Turbocharger and the Exhaust Manifold on Certain 3512B Marine Engines {1052, 1053}
Procedure to Route the Hose for the Jacket Water Around the Alternator Bracket{1380, 1383} Procedure to Route the Hose for the Jacket Water Around the Alternator Bracket{1380, 1383}
793F and 797F Off-Highway Trucks Chassis Electronic Control System MID 087 - CID 1428 - FMI 03
G3304B and G3306B Engines Radiator Group - Install
G3304B and G3306B Engines Gas Pressure Regulator - Disassemble
G3304B and G3306B Engines Gas Pressure Regulator - Assemble
C11 and C13 Engines Cylinder Head Valves
C13 Engine for Combat and Tactical Vehicles Air Lines
G3304B and G3306B Engines Gas Pressure Regulator - Install
C18 Marine Engine Plate Locations and Film Locations
C11 and C13 Engines Engine Oil Pump
G3304B and G3306B Engines Carburetor - Remove
C9.3 Engines for Caterpillar Built Machines Fuel Lines - Remove and Install
2009/06/01 Guidelines for Reusability of Cylinder Head Studs, Main Bearing Cap Studs, Main Bearing Cap Cross Tie Bolts, and Connecting Rod Cap Bolts and Nuts {1100, 1218, 1230}
G3304B and G3306B Engines Spark Plug - Test
Procedure to Rerate the Engine with Caterpillar Electronic Technician (ET) {1901, 1902, 1920} Procedure to Rerate the Engine with Caterpillar Electronic Technician (ET) {1901, 1902, 1920}