Gas Pressure Regulator - Disassemble
拆卸步骤
开始:
- 拆下气体压力调节器。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这将有助于防止污垢进入部件的内部。
- 将气管 (1) 从气体压力调节器 (2) 上拆下。
Show/hide table
图 1 | g01001902 |
- 将阀座 (3) 从气管上的三通接头上拆下。
Show/hide table
图 2 | g01004499 |
- 将挡圈和连接器从气体压力调节器上拆下。
- 将螺栓和盖 (4) 从气体压力调节器上拆下。
Show/hide table
图 3 | g01001904 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 将弹簧 (5) 和膜片组件 (7) 从气体压力调节器上拆下。
- 将阀 (6) 从气体压力调节器上拆下。
Caterpillar Information System:
G3304B and G3306B Engines Starting Air Pressure - Adjust
G3304B and G3306B Engines Air Starting Motor - Lubricate
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Replaced Relay or Solenoid Does Not Operate
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Transmission Does Not Automatically Shift Back Into Gear
G3304B and G3306B Engines Unburned Gas - Purge
G3304B and G3306B Engines Gas Pressure Regulator - Remove
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Transmission Does Not Automatically Shift Into Neutral
C9.3 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
G3304B and G3306B Engines Engine Support - Remove and Install
2009/06/08 Improved Hardware Is Used on the Sealing Joint between the Turbocharger and the Exhaust Manifold on Certain 3512B Marine Engines {1052, 1053}
Procedure to Route the Hose for the Jacket Water Around the Alternator Bracket{1380, 1383} Procedure to Route the Hose for the Jacket Water Around the Alternator Bracket{1380, 1383}
793F and 797F Off-Highway Trucks Chassis Electronic Control System MID 087 - CID 1428 - FMI 03
G3304B and G3306B Engines Gas Pressure Regulator - Assemble
C11 and C13 Engines Cylinder Head Valves
C13 Engine for Combat and Tactical Vehicles Air Lines
G3304B and G3306B Engines Gas Pressure Regulator - Install
C18 Marine Engine Plate Locations and Film Locations
C11 and C13 Engines Engine Oil Pump
G3304B and G3306B Engines Carburetor - Remove
C9.3 Engines for Caterpillar Built Machines Fuel Lines - Remove and Install
2009/06/01 Guidelines for Reusability of Cylinder Head Studs, Main Bearing Cap Studs, Main Bearing Cap Cross Tie Bolts, and Connecting Rod Cap Bolts and Nuts {1100, 1218, 1230}
G3304B and G3306B Engines Spark Plug - Test
Procedure to Rerate the Engine with Caterpillar Electronic Technician (ET) {1901, 1902, 1920} Procedure to Rerate the Engine with Caterpillar Electronic Technician (ET) {1901, 1902, 1920}
Failures of Cylinder Heads with the Intake Valves and Exhaust Valves in the Incorrect Positions{1100, 1105} Failures of Cylinder Heads with the Intake Valves and Exhaust Valves in the Incorrect Positions{1100, 1105}