Gas Pressure Regulator - Assemble
组装步骤
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零件。 棉绒可能会留在零件上,可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 将气门座 (3) 安装在气管上的三通接头上。
Show/hide table
图 1 | g01004499 |
- 将气门 (6) 安装在气体压力调节器上。 确保气门与杆 (8) 接合。
Show/hide table
图 2 | g01922136 |
- 将膜组件 (7) 安装在气体压力调节器上。 确保膜组件与杆 (8) 接合。
- 将弹簧 (5) 、盖 (4) 和螺栓安装在气体压力调节器上。
Show/hide table
图 3 | g01922137 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将连接器和挡圈安装在气体压力调节器上。
- 将气管 (1) 安装在气体压力调节器 (2) 上。
Show/hide table
图 4 | g01001902 |
End By: 安装气体压力调节器。
Caterpillar Information System:
G3304B and G3306B Engines Gas Pressure Regulator - Disassemble
G3304B and G3306B Engines Starting Air Pressure - Adjust
G3304B and G3306B Engines Air Starting Motor - Lubricate
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Replaced Relay or Solenoid Does Not Operate
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Transmission Does Not Automatically Shift Back Into Gear
G3304B and G3306B Engines Unburned Gas - Purge
G3304B and G3306B Engines Gas Pressure Regulator - Remove
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Transmission Does Not Automatically Shift Into Neutral
C9.3 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
G3304B and G3306B Engines Engine Support - Remove and Install
2009/06/08 Improved Hardware Is Used on the Sealing Joint between the Turbocharger and the Exhaust Manifold on Certain 3512B Marine Engines {1052, 1053}
Procedure to Route the Hose for the Jacket Water Around the Alternator Bracket{1380, 1383} Procedure to Route the Hose for the Jacket Water Around the Alternator Bracket{1380, 1383}
C11 and C13 Engines Cylinder Head Valves
C13 Engine for Combat and Tactical Vehicles Air Lines
G3304B and G3306B Engines Gas Pressure Regulator - Install
C18 Marine Engine Plate Locations and Film Locations
C11 and C13 Engines Engine Oil Pump
G3304B and G3306B Engines Carburetor - Remove
C9.3 Engines for Caterpillar Built Machines Fuel Lines - Remove and Install
2009/06/01 Guidelines for Reusability of Cylinder Head Studs, Main Bearing Cap Studs, Main Bearing Cap Cross Tie Bolts, and Connecting Rod Cap Bolts and Nuts {1100, 1218, 1230}
G3304B and G3306B Engines Spark Plug - Test
Procedure to Rerate the Engine with Caterpillar Electronic Technician (ET) {1901, 1902, 1920} Procedure to Rerate the Engine with Caterpillar Electronic Technician (ET) {1901, 1902, 1920}
Failures of Cylinder Heads with the Intake Valves and Exhaust Valves in the Incorrect Positions{1100, 1105} Failures of Cylinder Heads with the Intake Valves and Exhaust Valves in the Incorrect Positions{1100, 1105}
C11, C13 and C15 On-highway Engines 0173-00 High Exhaust Gas Temperature Derate