Housing (Front) - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 154-9731     | Thread Lock Compound     | -     |
B     | 8T-9022     | Silicone Gasket     | -     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine. |
- Thoroughly clean the mating surfaces of the plate and front housing (13) .
Note: The mating surfaces of the plate and the front housing must be free of oil, fuel, water, dirt, assembly compounds, and any other contaminants during assembly.
Show/hide table
Illustration 1 | g01097924 |
- Install a new gasket (15) on the plate.
Note: Trim the gasket even with the bottom of the front housing after assembly.
- Apply Tooling (B) to the bottom of gasket (15) in order to fill the space at the front housing and the engine oil pan.
- Install front housing (13) on the dowel pins on the cylinder block.
- Install bolts (14) that fasten the engine oil pan to the front housing.
- Install bolts (12) .
- Install bolt (10) and nut (9) .
- Install nuts (11) .
- Position strap (8) and install bolts (7) .
- Position bracket (3) and install bolts (2) .
Show/hide table
Illustration 2 | g01097597 |
- Install bolts (1) .
- Install nut (4) on the stud.
- Install bolts (5) that fasten the adapter and fuel transfer pump (6) to the plate.
End By:
- Install the engine support. Refer to Disassembly and Assembly, "Engine Support (Front) - Remove and Install".
- Install the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft Position Sensor - Remove and Install".
- Install the air compressor, if equipped. Refer to Disassembly and Assembly, "Air Compressor - Install".
- Install the crankshaft front seal and the wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Install".
- Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install".
- Install the expansion tank. Refer to Disassembly and Assembly, "Expansion Tank - Remove and Install".
Caterpillar Information System:
C18 Fire Pump Industrial Engine Housing (Front) - Remove
3516C HD Generator Set with Gearbox Emergency Stopping
TH55FT-E70 and TH55FT-E90 Transmissions Breather (Transmission) - Clean
R250 Automatic Voltage Regulator Remote Voltage Control
R250 Automatic Voltage Regulator Voltage - Adjust
R250 Automatic Voltage Regulator Stability - Adjust
Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230} Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230}
3516C Generator Sets Configuration Parameters
G3516 Petroleum Engines Crankcase Breather - Remove and Install
2008/10/01 A New Fuel Enable Valve Is Now Used {5479}
TH55FT-E70 and TH55FT-E90 Transmissions Safety Messages
3500B Generator Sets Safety Messages
C18 Fire Pump Industrial Engine Valve Mechanism Cover - Remove and Install
2009/01/26 Improved Fuel Injection Pump Timing Tool {1251}
PM3516 Power Modules Refill Capacities and Recommendations
C18 Fire Pump Industrial Engine Inlet Air Temperature Sensor - Remove and Install
3512B SR4B Generator Sets Radiator - Clean
C18 Fire Pump Industrial Engine Turbocharger Outlet Pressure Sensor - Remove and Install
C6.6 Marine Generator Set Engine Design
2008/10/27 A New Heat Shield for the Exhaust Manifold is Available {1067}
2008/12/15 A New Pressure Gauge Is Now Used. {7456}
Winding Insulation Maintenance and Cleaning and Drying of the Generators {4450} Winding Insulation Maintenance and Cleaning and Drying of the Generators {4450}
C18 Fire Pump Industrial Engine Electronic Control Module - Remove and Install
G3516 Petroleum Engines Fuel Control Actuator - Remove and Install