Radiator - Clean
注: 根据作业环境影响的情况调整清洁工作的频率。
检查散热器是否有以下情况: 散热器条损坏, 腐蚀, 脏污, 沾有油脂, 虫渍, 树叶, 机油 和 其他碎屑。 必要时清洁散热器。
Show/hide table
空气压力会造成人身伤害。 不按下面的适当步骤进行操作会造成人身伤害。 使用压缩空气时,戴防护面罩及穿防护服。 当空气喷嘴堵塞时, 清洁时使用的最大气压一定要降到 |
增压空气是清除松动碎屑的优选方法。 将压缩空气对着风扇气流相反的方向吹。 将喷嘴保持在距散热片大约
高压水也可用于清洗。 清洗用的最大水压必须低于
用去油剂和蒸气来清除机油和润滑脂。 清洁散热器芯两侧。 用去污剂和热水冲洗水箱芯。 用干净水彻底漂洗水箱芯。
清洁后,启动发动机并将发动机加速至高怠速。 这有助于清除碎屑和干燥水箱芯。 关闭发动机。 在散热器芯后面放一个灯泡来检查芯是否清洁。 必要时再次清洁。
检查散热片有无损坏。 弯曲了的散热片可用一把“梳刀”梳开。 检查以下部件是否状况良好:焊缝, 固定架, 空气管道, 连接件, 固定件 和 密封件。 如有必要,进行维修。
有关清洁和检查的更详细资料,请参阅专门出版物, SEBD0518, "冷却系统须知"。
根据散热器 OEM 提供的说明清洁散热器。
Caterpillar Information System:
C18 Fire Pump Industrial Engine Inlet Air Temperature Sensor - Remove and Install
PM3516 Power Modules Refill Capacities and Recommendations
2009/01/26 Improved Fuel Injection Pump Timing Tool {1251}
C18 Fire Pump Industrial Engine Valve Mechanism Cover - Remove and Install
C18 Fire Pump Industrial Engine Housing (Front) - Install
C18 Fire Pump Industrial Engine Housing (Front) - Remove
3516C HD Generator Set with Gearbox Emergency Stopping
TH55FT-E70 and TH55FT-E90 Transmissions Breather (Transmission) - Clean
R250 Automatic Voltage Regulator Remote Voltage Control
R250 Automatic Voltage Regulator Voltage - Adjust
R250 Automatic Voltage Regulator Stability - Adjust
Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230} Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230}
C18 Fire Pump Industrial Engine Turbocharger Outlet Pressure Sensor - Remove and Install
C6.6 Marine Generator Set Engine Design
2008/10/27 A New Heat Shield for the Exhaust Manifold is Available {1067}
2008/12/15 A New Pressure Gauge Is Now Used. {7456}
Winding Insulation Maintenance and Cleaning and Drying of the Generators {4450} Winding Insulation Maintenance and Cleaning and Drying of the Generators {4450}
C18 Fire Pump Industrial Engine Electronic Control Module - Remove and Install
G3516 Petroleum Engines Fuel Control Actuator - Remove and Install
C18 Fire Pump Industrial Engine Alternator - Remove and Install
C18 Fire Pump Industrial Engine Air Cleaner - Remove and Install
C18 Fire Pump Industrial Engine Expansion Tank - Remove and Install
C18 Fire Pump Industrial Engine Heat Exchanger - Remove
G3500B Engines Electrical Connectors