Pistons and Connecting Rods - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 5R-7425 | 盘车控制装置总成 (1) | 1 |
B | 1P-1861 | 挡圈钳 | 1 |
C | 271-0498 | 涨圈 | 1 |
D | 1U-7616 | 活塞环压缩器总成 | 1 |
E | 334-0519 | 润滑脂 | - |
Show/hide table
(1) | 9S-9082 发动机盘车工具是备用工具。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 当间隙检查完成后,安装连杆轴承,并保持干燥。 请参阅拆解与组装, "轴承间隙 – 检查"。 为了便于最终组装,在连杆轴承上涂抹清洁的发动机机油。
- 使用工具 (C) 在活塞上安装活塞环。
- 对于刮油环,确保弹簧末端与环开口成180度。 从环的间隙必须能看见弹簧的白色部分。
- 安装中间环时让有 "UP-2" 标记的一侧朝向活塞顶部。
- 安装上环,带有 "UP-1" 标记的一侧朝向活塞顶部。
- 安装挡圈后,旋转挡圈以确保间隙彼此相隔120度。 机油控制环形开口朝向活塞销的孔。
Show/hide table图 2 g03422729 - 使用清洁的发动机机油涂在活塞 (3) 孔、活塞销 (4) 上以及连杆 (5) 中的活塞销轴承上。 将连杆 (5) 放在活塞 (3) 内。 插入活塞销 (4) 使之穿过活塞 (3) 和轴承。
- 使用工具 (B) 安装挡圈 (6)。 挡圈 (6) 开口朝向活塞 (3) 的顶部。
- 将清洁的发动机机油涂抹在缸套孔、活塞环,以及活塞外表面上。
注: 确保将连杆和活塞安装进正确气缸中。
Show/hide table图 3 g02142782 - 使用工具 (A) 转动曲轴直到连杆轴颈位于底部中央位置。
- 用工具 (D)将活塞安装在缸套中。
注: 在安装活塞和连杆期间,小心不要损坏缸套或曲轴轴颈。
Show/hide table图 4 g00913801 Show/hide table图 5 g02143105 连杆盖的螺栓拧紧顺序 - 在连杆上安装连杆轴承的上半部分。 确保安装连杆轴承时使轴承凸舌卡进连杆凹槽中。 用干净的发动机油涂抹连杆轴承。 将连杆放置在曲轴轴径上。
- 在连杆盖 (2) 上安装连杆轴承的下半部分。 确保安装了连杆轴承,以使轴承凸舌卡进连杆盖凹槽中。 用干净的发动机油涂抹连杆轴承。
注: 连杆盖侧面上的编号必须紧接着该连杆侧面上的相应编号。 将连杆盖的斜面侧安装在曲轴的止推表面旁。
注: 翻新连杆没有针对气缸位置编号。
- 将工具 (E)涂抹在螺纹、摸柄和螺栓 (1)的底座上。
- 将连杆盖 (2) 就位。 安装螺栓 (1)。 采用以下步骤拧紧螺栓:
- 拧紧螺栓 (A) 和螺栓 (B) 至扭矩为
90 ± 5 N·m (65 ± 4 lb ft) 。 - 拧紧螺栓 (C) 和螺栓 (D) 至扭矩为
90 ± 5 N·m (65 ± 4 lb ft) 。 - 再次拧紧螺栓 (C) 和螺栓 (D) 至扭矩为
90 ± 5 N·m (65 ± 4 lb ft) 。 - 将指示标记置于螺栓和连杆盖上。 将每个螺栓都再拧紧 90 ± 5 度(1/4 圈)。
- 拧紧螺栓 (A) 和螺栓 (B) 至扭矩为
- 转动曲轴,以便确保曲轴能转动自如。
Show/hide table
图 1 | g01004841 |
结束:
- 安装活塞冷却喷嘴。 请参阅拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
- 安装缸盖。 请参阅拆解和组装, "缸盖 - 安装"。
Caterpillar Information System:
966M and 972M Wheel Loaders System Pressure Release
D10T2 Track-Type Tractor Machine Systems Implement Control Valve - Disassemble
966M and 972M Wheel Loaders Backup Alarm - Test - If Equipped
D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
C7.1 Engines Flywheel Housing - Remove and Install - Standard Housing
Check the Hydraulic Fan Pump on AD55B and AD60 Underground Articulated Trucks{1387, 5070} Check the Hydraulic Fan Pump on AD55B and AD60 Underground Articulated Trucks{1387, 5070}
3500 Engines Pistons and Connecting Rods - Remove
966M and 972M Wheel Loaders Bucket Linkage and Loader Cylinder Bearings - Lubricate
D10T2 Track-Type Tractor Machine Systems Refrigerant Condenser - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Engine Supplement Fan Blade (Spider) - Remove and Install
D6N Track-Type Tractor Transmission Breather - Clean/Replace
D10T2 Track-Type Tractor Machine Systems Piston Pump (Fan Charge and Pilot Pressure) - Remove and Install
966H and 972H Wheel Loaders PowerTrain Carrier Bearing (Drive Shaft) - Remove and Install
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Modulating Valve (Transmission Clutch) - Install
966M and 972M Wheel Loaders Capacities (Refill)
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Modulating Valve (Transmission Clutch) - Remove
966H and 972H Wheel Loaders PowerTrain Drive Shaft (Center) - Remove and Install
966H and 972H Wheel Loaders PowerTrain Drive Shaft (Rear) - Remove and Install
966H and 972H Wheel Loaders PowerTrain Tire and Rim (Front) - Remove and Install
980M Tier 4 and 982M Tier 4 Wheel Loaders Power Train Torque Converter, Transmission and Output Transfer Gears - Remove
966H and 972H Wheel Loaders PowerTrain Trunnion Support (Oscillating Axle, Rear) - Remove and Install
D6T Track-Type Tractor Window Washer Reservoir - Fill
D10T2 Track-Type Tractor Machine Systems Implement Control Valve - Assemble
2013/08/28 An Improved Service Brake Hose is Used on Certain 966H and 972H Wheel Loaders {4257, 5057}