Pistons and Connecting Rods - Remove
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 5R-7425 | 盘车控制装置总成 (1) | 1 |
| B | 1P-1861 | 挡圈钳 | 1 |
| C | 271-0498 | 涨圈 | 1 |
Show/hide table
| (1) | 9S-9082 发动机盘车工具是备用工具。 |
开始:
- 拆下缸盖。 请参阅拆解和组装, "缸盖 - 拆卸"。
- 拆下活塞冷却喷嘴。 请参阅拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 用工具 (A)转动曲轴，直至可以拆下螺栓 (1)。
- 从缸套内表面顶部开始清除积碳凸起。
- 检查连杆和连杆盖上的识别标记是否正确。 连杆和连杆盖侧面应该有蚀刻的编号。 该编号必须与气缸号一致。 如有必要，标记连杆和连杆盖。
注: 请勿压印连杆组件。
- 拆下螺栓 (1) 和连杆盖 (2)。 推动连杆直到活塞环脱出缸套。
- 将活塞和连杆从缸套中拆下。
注: 在拆卸活塞和连杆期间，小心不要损坏缸套或曲轴轴颈。
Show/hide table
图 2 g03422403 - 使用工具 (B) 拆下固定活塞销 (4) 的挡圈 (6)。 拆卸活塞销 (4)。 从连杆 (5) 上拆卸活塞 (3)。
- 将轴承从连杆 (5)和连杆盖上拆下。
注: 如有必要，将活塞裙从活塞顶上分开。
Show/hide table图 3 g00913818 - 使用工具 (C) 从活塞 (3) 上拆卸活塞环 (6)。
Show/hide table
| |
| 图 1 | g00913801 |
Caterpillar Information System:
966M and 972M Wheel Loaders Bucket Linkage and Loader Cylinder Bearings - Lubricate
D10T2 Track-Type Tractor Machine Systems Refrigerant Condenser - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Engine Supplement Fan Blade (Spider) - Remove and Install
D6N Track-Type Tractor Transmission Breather - Clean/Replace
D10T2 Track-Type Tractor Machine Systems Piston Pump (Fan Charge and Pilot Pressure) - Remove and Install
980H Wheel Loader Engine Supplement Refrigerant Compressor - Remove and Install
D6T Track-Type Tractor Track - Check/Adjust
621K, 623K, and 627K Wheel Tractor-Scrapers Systems Control Valve (Implement) - 621K and 627K
836K Landfill Compactor, 834K Wheel Dozer and 988K Wheel Loader C18 Engine Supplement Engine Oil Cooler - Remove and Install
D10T2 Track-Type Tractor Machine Systems Pilot Oil Accumulator - Remove and Install
901C, 902C and 903C Compact Wheel Loaders PowerTrain Differential (Standard) - Assemble
D6T Track-Type Tractor Torque Converter Scavenge Screen - Clean
Check the Hydraulic Fan Pump on AD55B and AD60 Underground Articulated Trucks{1387, 5070} Check the Hydraulic Fan Pump on AD55B and AD60 Underground Articulated Trucks{1387, 5070}
C7.1 Engines Flywheel Housing - Remove and Install - Standard Housing
D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
966M and 972M Wheel Loaders Backup Alarm - Test - If Equipped
D10T2 Track-Type Tractor Machine Systems Implement Control Valve - Disassemble
966M and 972M Wheel Loaders System Pressure Release
3500 Engines Pistons and Connecting Rods - Install
966H and 972H Wheel Loaders PowerTrain Carrier Bearing (Drive Shaft) - Remove and Install
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Modulating Valve (Transmission Clutch) - Install
966M and 972M Wheel Loaders Capacities (Refill)
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Modulating Valve (Transmission Clutch) - Remove
966H and 972H Wheel Loaders PowerTrain Drive Shaft (Center) - Remove and Install