Implement Control Valve - Disassemble
拆卸步骤
开始:
- 拆下机具控制阀。
- 拆下管组件 (1) 。
Show/hide table
 | |
| 图 1 | g03422581 |
- 拆下螺母 (2) 和盖 (3) 。
Show/hide table
 | |
| 图 2 | g03422598 |
- 拆下 O 形密封圈 (4) 和 (5) 。 拆下密封件 (6) 。
Show/hide table
 | |
| 图 3 | g03422615 |
- 拆下阀总成 (7) 。
Show/hide table
 | |
| 图 4 | g03422629 |
- 拆下电磁阀 (8) 和壳体组件 (9) 。 对另一侧重复此操作。
Show/hide table
 | |
| 图 5 | g03422665 |
- 分离电磁阀 (8) 与壳体组件 (9) 。 拆下 O 形密封圈 (10) 。
Show/hide table
 | |
| 图 6 | g03422667 |
- 拆下挡圈 (11) 、弹簧 (12) 、挡圈 (13) 和阀杆 (14) 。
Show/hide table
 | |
| 图 7 | g03422638 |
- 拆下螺塞 (15) 和 (17) 。 从螺塞 (15) 和 (17) 上拆下所有密封。 卸下 O 形密封圈 (16) 。
Show/hide table
 | |
| 图 8 | g03422656 |
- 对于其余的阀总成，重复步骤 4 至 8。
- 将杆 (18) 从歧管 (19) 上拆下。
Show/hide table
 | |
| 图 9 | g03422692 |
- 拆下阀 (20) 和 O 形密封圈 (21) 。 拆下适配器 (22) 。
Show/hide table
 | |
| 图 10 | g03422696 |
- 拆下传感器组件 (23) 。 拆下适配器 (24) 。
Show/hide table
 | |
| 图 11 | g03422711 |
- 拆下安全阀 (27) 。 拆下 O 形密封圈 (25) 和 (26) 。
Show/hide table
 | |
| 图 12 | g03422745 |
Caterpillar Information System:
966M and 972M Wheel Loaders Backup Alarm - Test - If Equipped
D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
C7.1 Engines Flywheel Housing - Remove and Install - Standard Housing
Check the Hydraulic Fan Pump on AD55B and AD60 Underground Articulated Trucks{1387, 5070} Check the Hydraulic Fan Pump on AD55B and AD60 Underground Articulated Trucks{1387, 5070}
3500 Engines Pistons and Connecting Rods - Remove
966M and 972M Wheel Loaders Bucket Linkage and Loader Cylinder Bearings - Lubricate
D10T2 Track-Type Tractor Machine Systems Refrigerant Condenser - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Engine Supplement Fan Blade (Spider) - Remove and Install
D6N Track-Type Tractor Transmission Breather - Clean/Replace
D10T2 Track-Type Tractor Machine Systems Piston Pump (Fan Charge and Pilot Pressure) - Remove and Install
980H Wheel Loader Engine Supplement Refrigerant Compressor - Remove and Install
D6T Track-Type Tractor Track - Check/Adjust
966M and 972M Wheel Loaders System Pressure Release
3500 Engines Pistons and Connecting Rods - Install
966H and 972H Wheel Loaders PowerTrain Carrier Bearing (Drive Shaft) - Remove and Install
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Modulating Valve (Transmission Clutch) - Install
966M and 972M Wheel Loaders Capacities (Refill)
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Modulating Valve (Transmission Clutch) - Remove
966H and 972H Wheel Loaders PowerTrain Drive Shaft (Center) - Remove and Install
966H and 972H Wheel Loaders PowerTrain Drive Shaft (Rear) - Remove and Install
966H and 972H Wheel Loaders PowerTrain Tire and Rim (Front) - Remove and Install
980M Tier 4 and 982M Tier 4 Wheel Loaders Power Train Torque Converter, Transmission and Output Transfer Gears - Remove
966H and 972H Wheel Loaders PowerTrain Trunnion Support (Oscillating Axle, Rear) - Remove and Install
D6T Track-Type Tractor Window Washer Reservoir - Fill