D10T2 Track-Type Tractor Machine Systems Caterpillar


Refrigerant Condenser - Remove and Install

Usage:

D10T2 JJW

拆卸步骤


注意

在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。

有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。

按照当地法规和要求处置所有液体。


------ WARNING! ------

接触制冷剂会使人受伤。

接触制冷剂会造成冻伤。 让手、脸避开,有助于防止受伤。

制冷管路被打开时,即使压力计显示系统中已经没有制冷剂,也要始终戴着护目镜。

拆卸管件时,务必小心谨慎。 慢慢地拧松接头。 如果系统内仍有压力,就要把它缓慢地释放到一个通风良好的地方去。

通过燃着的香烟吸入制冷剂会使人受伤或死亡。

通过燃着的香烟或其他抽烟方法吸入空调制冷气体,或者,吸入空调制冷气体接触明火而形成的烟雾,都会造成对人体的伤害 或死亡。

维修空调时,或者,在任何可能存在制冷气体的地方都不要抽烟。

采用经过认可的回收和循环利用车妥善地从空调器中取出制冷剂。


  1. 回收空调系统中的空调制冷剂。 请参阅维修手册, SENR5664, "适用于所有 Caterpillar 机器的所有空调和暖风用产品",以了解正确步骤。 请参阅专门出版物, NENG2500, "空调工具"以了解正确的工具信息。



    图 1g03422334

  1. 断开线束组件 (1) 。 断开软管组件 (2) 。



    图 2g03422348



    图 3g03422359

  1. 将工具 (A) 和适当的起吊设备固定到制冷剂冷凝器 (3) 上。 制冷剂冷凝器 (3) 的重量约为 32 kg (70 lb)。

  1. 拆下安装螺栓 (4) 。 拆下制冷剂冷凝器 (3) 。

安装步骤

  1. 按与拆卸相反的顺序安装制冷剂冷凝器 (3) 。

Caterpillar Information System:

990K Wheel Loader and 844K Wheel Dozer Engine Supplement Fan Blade (Spider) - Remove and Install
D6N Track-Type Tractor Transmission Breather - Clean/Replace
D10T2 Track-Type Tractor Machine Systems Piston Pump (Fan Charge and Pilot Pressure) - Remove and Install
980H Wheel Loader Engine Supplement Refrigerant Compressor - Remove and Install
D6T Track-Type Tractor Track - Check/Adjust
621K, 623K, and 627K Wheel Tractor-Scrapers Systems Control Valve (Implement) - 621K and 627K
836K Landfill Compactor, 834K Wheel Dozer and 988K Wheel Loader C18 Engine Supplement Engine Oil Cooler - Remove and Install
D10T2 Track-Type Tractor Machine Systems Pilot Oil Accumulator - Remove and Install
901C, 902C and 903C Compact Wheel Loaders PowerTrain Differential (Standard) - Assemble
D6T Track-Type Tractor Torque Converter Scavenge Screen - Clean
Check the Transmission Input Yoke on AD55B and AD60 Underground Articulated Trucks{3063, 3253} Check the Transmission Input Yoke on AD55B and AD60 Underground Articulated Trucks{3063, 3253}
D6T Track-Type Tractor Ripper Linkage and Cylinder Bearings - Lubricate
966M and 972M Wheel Loaders Bucket Linkage and Loader Cylinder Bearings - Lubricate
3500 Engines Pistons and Connecting Rods - Remove
Check the Hydraulic Fan Pump on AD55B and AD60 Underground Articulated Trucks{1387, 5070} Check the Hydraulic Fan Pump on AD55B and AD60 Underground Articulated Trucks{1387, 5070}
C7.1 Engines Flywheel Housing - Remove and Install - Standard Housing
D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} D6N Track-Type Tractor TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
966M and 972M Wheel Loaders Backup Alarm - Test - If Equipped
D10T2 Track-Type Tractor Machine Systems Implement Control Valve - Disassemble
966M and 972M Wheel Loaders System Pressure Release
3500 Engines Pistons and Connecting Rods - Install
966H and 972H Wheel Loaders PowerTrain Carrier Bearing (Drive Shaft) - Remove and Install
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Modulating Valve (Transmission Clutch) - Install
966M and 972M Wheel Loaders Capacities (Refill)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.