Electronic Control Module (ECM) - Configure
检查配置屏幕可解决机器问题。 部件故障可识别为以下项:
- 未安装该部件。
- 已安装该部件但需要更改安装以排除故障。
需要利用 Cat® 电子技师(Cat® ET)维修工具配置新电子控制模块(ECM)。
配置 ECM 所需工具见表 1 中所示。
Show/hide table
所需工具     | ||
零件号     | 说明     | 数量     |
317-7484     | Caterpillar® 电子技师 (Cat® ET)     | 1     |
317-7485     | 通信适配器 III     | 1     |
317-7487     | USB 至 PC 电缆     | 1     |
327-8981     | 数据链路电缆     | 1     |
Cat® ET 的步骤
- 把钥匙开关转到断开位置。
- 将通信适配器和个人电脑(PC)连接至诊断维修工具接头。
Show/hide table
图 1 | g01896613 |
位于数据链路两个座椅之间的维修工具接头的典型视图。 |
- 将钥匙开关转到 RUN(运转)位置。
- 在您的电脑上,启动 Cat ET。
- Cat ET 将触发与机器上 ECM 间的通信。
- 选择手动配置 ECM。
注: 选择控制装置时,ECM 上将有一个激活的诊断代码,指示需要的参数尚未编程设定。 编程设定参数后,该诊断代码将自动清除。
- 在 Cat ET 的顶部菜单栏,选择 "Service(维修)"并点击 "Configuration(配置)"。 功能键 "F5" 将打开配置屏幕。
- 打开/展开顶部列出的 "Configuration Gp(配置组)"。
- 如需更改机器序列号,双击 "Product ID(产品 ID)"或 "Equipment ID(设备 ID)"。(或突出显示 ID 并点击 "Change(更改)"按钮)。 "Change Parameter Value(更改参数值)"将打开。 对于 "New Value(新值)",输入正确的序列号并点击 "OK(确定)"按钮。 点击 "Yes(是)"按钮完成新值。
注: 如果未选择正确的序列号,则可能会影响机器性能。
- 根据需要检查并编辑部件操作或特性值。 其它配置的更改请遵循上一步骤中所用的相同类型的编程步骤。
- 完成手动编程配置时,用钥匙开关循环电源。
- 让钥匙开关保持在断开位置至少十秒。
- 钥匙开关回到运转位置后,Cat ET 将发起与机器 ECM 的通信。
注: 使用 "Copy Configuration > ECM Replacement(复制配置 > ECM 更换)"记录和保存更新的配置参数。
Caterpillar Information System:
3500B Industrial Engines with the ADEM 3 Electronic Control Module Emergency Stop Switch
C9 On-highway Engine Fuel Control Manifold (ARD) - Assemble
C9 On-highway Engine Fuel Control Manifold (ARD) - Disassemble
TA19-M2WD and TA19-M4WD Agricultural Transmissions Pump Drive - Remove
C27 and C32 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine Accessory Drive - Assemble
C7 On-Highway Engine Fuel Transfer Pump - Install
3412E and C30 Marine Engines Cooling System Coolant (ELC) - Change
C13 Engine Accessory Drive - Disassemble
3412E and C30 Marine Engines Cooling System Coolant (DEAC) - Change
G3304 and G3306 Engines Coolant Level Sensor
C7 On-Highway Engine Fuel Transfer Pump - Remove
C7 On-Highway Engine Clean Gas Induction Valve - Disassemble
C11, C13, and C15 On-highway Engines Fuel System Primary Filter - Replace
3500B Industrial Engines with the ADEM 3 Electronic Control Module Ether Injection System
C7 On-Highway Engine Flame Detection Temperature Sensor - Remove and Install
3500B Industrial Engines with the ADEM 3 Electronic Control Module Engine Speed/Timing Sensor
C7 On-Highway Engine Turbocharger Outlet Temperature Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Base - Remove - C27
C7 On-Highway Engine Atmospheric Pressure Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Base - Install - C27
C7 On-Highway Engine Inlet Air Temperature Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install - C27
C27 and C32 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - C27