Fuel Control Manifold (ARD) - Disassemble
Disassembly Procedure
Start By:
- Remove the fuel manifold. Refer to Disassembly and Assembly, "Fuel Control Manifold (ARD) - Remove".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove tube assembly (1) .
Show/hide table
Illustration 1 | g01265718 |
- Remove nut (2), washer (2), coil assembly (4), and valve assembly (5). Remove O-ring seals (6) from valve assembly (5) .
Show/hide table
Illustration 2 | g01265721 |
- Remove nut (7), washer (8), coil assembly (9), and valve assembly (10). Remove O-ring seals (11) from valve assembly (10). Repeat for the remaining solenoid valve.
Show/hide table
Illustration 3 | g01265722 |
- Remove check valve (12). Remove O-ring seals (13) from check valve (12) .
Show/hide table
Illustration 4 | g01265739 |
- Remove check valve (14). Remove O-ring seals (15) from check valve (14) .
Show/hide table
Illustration 5 | g01265741 |
Caterpillar Information System:
TA19-M2WD and TA19-M4WD Agricultural Transmissions Pump Drive - Remove
C27 and C32 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine Accessory Drive - Assemble
C7 On-Highway Engine Fuel Transfer Pump - Install
3412E and C30 Marine Engines Cooling System Coolant (ELC) - Change
C13 Engine Accessory Drive - Disassemble
3412E and C30 Marine Engines Cooling System Coolant (DEAC) - Change
G3304 and G3306 Engines Coolant Level Sensor
C7 On-Highway Engine Fuel Transfer Pump - Remove
TA19-M2WD and TA19-M4WD Agricultural Transmissions Relief Valve (Transmission Main) - Install
TA19-M2WD and TA19-M4WD Agricultural Transmissions Relief Valve (Transmission Main) - Remove
3500B Industrial Engines with the ADEM 3 Electronic Control Module Electrical Power Supply
C9 On-highway Engine Fuel Control Manifold (ARD) - Assemble
3500B Industrial Engines with the ADEM 3 Electronic Control Module Emergency Stop Switch
770, 772, 773E, 773F, 777E and 777F Off-Highway Trucks and 775F Quarry Truck VIMS Truck Payload System Electronic Control Module (ECM) - Configure
C7 On-Highway Engine Clean Gas Induction Valve - Disassemble
C11, C13, and C15 On-highway Engines Fuel System Primary Filter - Replace
3500B Industrial Engines with the ADEM 3 Electronic Control Module Ether Injection System
C7 On-Highway Engine Flame Detection Temperature Sensor - Remove and Install
3500B Industrial Engines with the ADEM 3 Electronic Control Module Engine Speed/Timing Sensor
C7 On-Highway Engine Turbocharger Outlet Temperature Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Base - Remove - C27
C7 On-Highway Engine Atmospheric Pressure Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Base - Install - C27