Fuel System Primary Filter - Replace
Show/hide table
 |
|
渗漏或溅溢到热表面或电气部件上的燃油会引起失火。 为防止可能的伤害，当更换燃油滤清器或油水分离器滤芯时，要将起动开关断开。 应立即将溅溢的燃油清除干净。 |
Show/hide table
| 注意 |
|---|
|
不要让脏物进入燃油系统。 彻底清洁要拆开的燃油系统部件的周围区域。 在所有拆开的燃油系统部件上安放适当的盖。 |
Show/hide table
| 注意 |
|---|
|
在检查、保养、测试、调整及维修产品时，请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前，请准备好盛接液体用的适当容器。 有关适于收集和盛放 Cat 产品油液的工具和用品，请参阅专门出版物, NENG2500, "Cat 代理商维修工具目录"或专门出版物, PECJ0003, "Cat 车间用品和工具目录"。 按照本地法规和要求处置所有油液。 |
注: 卡特彼勒要求使用绝对值为 10 微米 (c) 至 15 微米 (c) 燃油粗滤器过滤所有燃油。
有关燃油粗滤器保养的更多资料，请参阅车辆的原设备制造厂提供的资料。
Caterpillar Information System:
C7 On-Highway Engine Clean Gas Induction Valve - Disassemble
770, 772, 773E, 773F, 777E and 777F Off-Highway Trucks and 775F Quarry Truck VIMS Truck Payload System Electronic Control Module (ECM) - Configure
3500B Industrial Engines with the ADEM 3 Electronic Control Module Emergency Stop Switch
C9 On-highway Engine Fuel Control Manifold (ARD) - Assemble
C9 On-highway Engine Fuel Control Manifold (ARD) - Disassemble
TA19-M2WD and TA19-M4WD Agricultural Transmissions Pump Drive - Remove
C27 and C32 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine Accessory Drive - Assemble
C7 On-Highway Engine Fuel Transfer Pump - Install
3412E and C30 Marine Engines Cooling System Coolant (ELC) - Change
C13 Engine Accessory Drive - Disassemble
3412E and C30 Marine Engines Cooling System Coolant (DEAC) - Change
3500B Industrial Engines with the ADEM 3 Electronic Control Module Ether Injection System
C7 On-Highway Engine Flame Detection Temperature Sensor - Remove and Install
3500B Industrial Engines with the ADEM 3 Electronic Control Module Engine Speed/Timing Sensor
C7 On-Highway Engine Turbocharger Outlet Temperature Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Base - Remove - C27
C7 On-Highway Engine Atmospheric Pressure Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Base - Install - C27
C7 On-Highway Engine Inlet Air Temperature Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install - C27
C27 and C32 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - C27
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head - Remove - C27
C9 On-highway Engine Gear Group (Rear)