Flame Detection Temperature Sensor - Remove and Install
Removal Procedure
- Remove cable strap (1) .
Show/hide table
Illustration 1 | g02159638 |
- Disconnect harness assembly (2) and harness assembly (3) .
Note: Harness assembly (2) contains the flame detection temperature sensor and the turbocharger outlet temperature sensor. Harness assembly (3) contains the flame boundary temperature sensor.
- Remove flame detection temperature sensor (4) .
Show/hide table
Illustration 2 | g02159639 |
- Remove flame boundary temperature sensor (5) .
Show/hide table
Illustration 3 | g02159666 |
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 5P-3931     | Anti-Seize Compound     | -     |
- Apply Tooling (A) to the threads of the flame boundary temperature sensor (5) . Install flame boundary temperature sensor (5) . Tighten flame boundary temperature sensor (5) to a torque of 45 ± 5 N·m (33 ± 4 lb ft).
Show/hide table
Illustration 4 | g02159666 |
- Apply Tooling (A) to the threads of flame detection temperature sensor (4) . Install flame detection temperature sensor (4) . Tighten flame detection temperature sensor (4) to a torque of 45 ± 5 N·m (33 ± 4 lb ft).
Show/hide table
Illustration 5 | g02159639 |
- Connect harness assembly (3) and harness assembly (2) .
Show/hide table
Illustration 6 | g02159638 |
- Install a new cable strap (1) .
Caterpillar Information System:
3500B Industrial Engines with the ADEM 3 Electronic Control Module Ether Injection System
C11, C13, and C15 On-highway Engines Fuel System Primary Filter - Replace
C7 On-Highway Engine Clean Gas Induction Valve - Disassemble
770, 772, 773E, 773F, 777E and 777F Off-Highway Trucks and 775F Quarry Truck VIMS Truck Payload System Electronic Control Module (ECM) - Configure
3500B Industrial Engines with the ADEM 3 Electronic Control Module Emergency Stop Switch
C9 On-highway Engine Fuel Control Manifold (ARD) - Assemble
C9 On-highway Engine Fuel Control Manifold (ARD) - Disassemble
TA19-M2WD and TA19-M4WD Agricultural Transmissions Pump Drive - Remove
C27 and C32 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine Accessory Drive - Assemble
C7 On-Highway Engine Fuel Transfer Pump - Install
3412E and C30 Marine Engines Cooling System Coolant (ELC) - Change
3500B Industrial Engines with the ADEM 3 Electronic Control Module Engine Speed/Timing Sensor
C7 On-Highway Engine Turbocharger Outlet Temperature Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Base - Remove - C27
C7 On-Highway Engine Atmospheric Pressure Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Base - Install - C27
C7 On-Highway Engine Inlet Air Temperature Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install - C27
C27 and C32 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - C27
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head - Remove - C27
C9 On-highway Engine Gear Group (Rear)
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head - Install - C27
C175-16 and C175-20 Generator Set Engines Valve Mechanism