2004/03/29 Caterpillar


Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}

Usage:

D3400 01T
Articulated Truck:
  • All
    Asphalt Paver:
  • All
    Challenger:
  • All
    Cold Planer:
  • All
    Combine:
  • All
    Commercial Engines and Truck Engines:
  • All
    Earthmoving Compactor:
  • All
    Excavator:
  • All
  • All 300B Family Excavators
  • All 300C Family Excavators
    Forest Products:
  • All
    Motor Grader:
  • All
    Off-Highway Truck/Tractor:
  • All
    Pipelayer:
  • All
    Road Reclaimer/Soil Stabilizer:
  • All
    Soil Compactor:
  • All
    Track-Type Loader:
  • All
    Track-Type Skidder:
  • All
    Track-Type Tractor:
  • All
    Wheel Dozer:
  • All
    Wheel Loader:
  • All
  • An fuel priming pump is available for your Caterpillar equipment with a 24 volt system.

    The fuel priming pump reduces the time that is needed in order to prime the fuel system. The fuel priming pump will help eliminate contamination of the fuel supply.

    This Special Instruction has been revised in order to add the following products:

    • Off-Highway Truck/Tractor

    • Wheel Dozer

    • Wheel Loader

    This Special Instruction is available through the normal literature distribution system. The publication can also be found on the Caterpillar Service Information System (SIS).

    Caterpillar Information System:

    C15 On-Highway Engine Engine Oil Pump - Assemble
    C15 On-Highway Engine Engine Oil Pump - Disassemble
    C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
    3524B Engines for 797 and 797B Off-Highway Trucks Cold Mode Operation
    C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
    C9 Marine Auxiliary and Marine Generator Set Engines Speed Control (Switch) - Test
    C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Assemble
    C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Disassemble
    C32 Marine Engine Plate Locations and Film Locations
    C9 Marine Auxiliary and Marine Generator Set Engines Switch Circuits - Test
    Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
    C-15, C-16 and C-18 Truck Engines Pistons and Connecting Rods - Install
    C9 Marine Auxiliary and Marine Generator Set Engines Air Inlet Heater Circuit - Test
    2003/12/01 New Procedures Will Increase Power Module Reliability {7273}
    C18 Marine Auxiliary Engines E096 High Fuel Pressure
    C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
    C15 Engine Cooling System Coolant (DEAC) - Change
    C15 Engine Cooling System Coolant (ELC) - Change
    C15 and C18 Generator Set Engines Inlet and Exhaust Valves - Remove and Install
    G3500 Engines Detonation Sensors
    C13, C15, and C18 Generator Set Engines E197 High Engine Oil Temperature
    C9 Marine Auxiliary and Marine Generator Set Engines Diagnostic Codes
    C18 Marine Auxiliary Engines E198 Low Fuel Pressure
    C15 and C18 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Remove - If Equipped
    Back to top
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.