Turbocharger - Disassemble
拆解步骤
开始:
- 拆下涡轮增压器。 请参阅拆解和组装, "涡轮增压器 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 从压缩机壳体上断开软管 (6) 。
Show/hide table
图 1 | g02562158 |
- 松开 V 形带箍 (2) 和 (4) 。
- 将压缩机壳体 (5) 和涡轮增压器芯 (3) 分离。
- 将涡轮壳体 (1) 和涡轮增压器芯 (3) 分离。
- 拆下螺栓 (7) 、盖 (8) ,然后拆下密封垫(未显示)。 对所有其他盖重复此步骤。
Show/hide table
注意 |
---|
请勿尝试拆解涡轮增压器芯组件或废气旁通阀。 请勿拆下压缩机叶轮。 涡轮增压器芯组件和废气旁通阀均不可维修,仅应作为整体进行更换。 |
Caterpillar Information System:
C32 Marine Engine Plate Locations and Film Locations
C9 Marine Auxiliary and Marine Generator Set Engines Switch Circuits - Test
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C-15, C-16 and C-18 Truck Engines Pistons and Connecting Rods - Install
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Install
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Remove
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Guides - Remove and Install
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Seat Inserts - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
C27 and C32 Generator Set Engines Electronic Unit Injector Sleeve - Install
C15 Petroleum Engines Electronic Unit Injector Sleeve - Remove
Solenoid (Starting Motor) − Replace{1467} Solenoid (Starting Motor) − Replace{1467}
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Assemble
C9 Marine Auxiliary and Marine Generator Set Engines Speed Control (Switch) - Test
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
3524B Engines for 797 and 797B Off-Highway Trucks Cold Mode Operation
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C15 On-Highway Engine Engine Oil Pump - Disassemble
C15 On-Highway Engine Engine Oil Pump - Assemble
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
C9 Marine Auxiliary and Marine Generator Set Engines Air Inlet Heater Circuit - Test
2003/12/01 New Procedures Will Increase Power Module Reliability {7273}
C18 Marine Auxiliary Engines E096 High Fuel Pressure
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install