Electronic Unit Injector Sleeve - Remove
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A(1) | 128-7889 | Bridge Puller | 1 |
221-9778 | Puller Stud | 1 | |
9U-6877 | Thrust Bearing | 1 | |
5P-8247 | Hard Washer | 1 | |
4K-0367 | Nut | 1 |
Show/hide table
(1) | Part of the 9U-6891 Injector Tool Group |
Start By:
- Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Drain the coolant from the engine. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change". Coolant will enter the cylinder if the cooling system is not drained.
Show/hide table
Illustration 1 g01043124 - Install Tooling (A) in electronic unit injector sleeve (1).
- Tighten the nut on Tooling (A) until the electronic unit injector sleeve is pulled free of the cylinder head.
- Remove Tooling (A) from the electronic unit injector sleeve.
Show/hide table
Illustration 2 g01073635 - Remove the O-ring seals (2) and O-ring seal (3) from electronic unit injector sleeve (1).
Caterpillar Information System:
Solenoid (Starting Motor) − Replace{1467} Solenoid (Starting Motor) − Replace{1467}
C18 Marine Auxiliary Engines System Configuration Parameters
C15 Generator Sets Walk-Around Inspection
C15 and C18 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
2003/12/01 Uninterruptible Power Supply (UPS) Flywheel Bearing Upgrade {7551}
C32 Marine Engine Diagnostic Flash Code Retrieval
C9 Marine Auxiliary and Marine Generator Set Engines Engine Temperature Sensor Open or Short Circuit - Test
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Cooler - Install
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
3406E and C15 Marine Engines Fuel System
C32 Marine Engine Air Lines
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Filter Base - Disassemble
C27 and C32 Generator Set Engines Electronic Unit Injector Sleeve - Install
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Guides - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Remove
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Install
C-15, C-16 and C-18 Truck Engines Pistons and Connecting Rods - Install
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C9 Marine Auxiliary and Marine Generator Set Engines Switch Circuits - Test
C32 Marine Engine Plate Locations and Film Locations
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Assemble