Turbocharger - Assemble
组装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
压缩机壳体必须在涡轮增压器组件上保持平直不倾斜。 倾斜可能会导致压缩机叶片倾翻或导致压缩机轴损坏。 |
- 将盖 (8) 和密封垫(未显示)放置到位。 安装螺栓 (7) 并用手拧紧。 将螺栓 (7) 拧紧至扭矩为 25 ± 6 N·m (18 ± 4 lb ft)。 将螺栓 (7) 拧紧到 47 ± 9 N·m (35 ± 6 lb ft) 的最终扭矩。 对所有其他盖重复此步骤。
Show/hide table
图 1 | g02562280 |
- 将压缩机壳体 (5) 和涡轮壳体 (1) 放置到涡轮增压器芯 (3) 上。
- 拧紧 V 形带箍 (2) 上的螺母至扭矩为 17 ± 1 N·m (124 ± 9 lb in)。 用软面锤轻轻敲击卡箍直径周围区域。 将螺母重新上紧到 17 ± 1 N·m (124 ± 9 lb ft) 的扭矩。
注: 确保配合面平整。
- 拧紧 V 形带箍 (4) 上的螺母至扭矩为 17 ± 1 N·m (124 ± 9 lb in)。 用软面锤轻轻敲击卡箍直径周围区域。 将螺母重新上紧到 17 ± 1 N·m (124 ± 9 lb ft) 的扭矩。
- 确保叶轮可以自由旋转。
- 将软管 (6) 连接到压缩机壳体上。
End By: 安装涡轮增压器。 请参阅 拆解和组装, "涡轮增压器 - 安装"。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Disassemble
C32 Marine Engine Plate Locations and Film Locations
C9 Marine Auxiliary and Marine Generator Set Engines Switch Circuits - Test
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C-15, C-16 and C-18 Truck Engines Pistons and Connecting Rods - Install
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Install
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Remove
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Guides - Remove and Install
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Seat Inserts - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
C27 and C32 Generator Set Engines Electronic Unit Injector Sleeve - Install
C15 Petroleum Engines Electronic Unit Injector Sleeve - Remove
C9 Marine Auxiliary and Marine Generator Set Engines Speed Control (Switch) - Test
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
3524B Engines for 797 and 797B Off-Highway Trucks Cold Mode Operation
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C15 On-Highway Engine Engine Oil Pump - Disassemble
C15 On-Highway Engine Engine Oil Pump - Assemble
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
C9 Marine Auxiliary and Marine Generator Set Engines Air Inlet Heater Circuit - Test
2003/12/01 New Procedures Will Increase Power Module Reliability {7273}
C18 Marine Auxiliary Engines E096 High Fuel Pressure
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
C15 Engine Cooling System Coolant (DEAC) - Change