Engine Oil Pump - Remove
开始:
- 卸下发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆卸螺栓 (2)。 拆卸管组件 (1)。 从管组件上拆卸 O 形密封圈。
- 拆卸螺栓 (6) 和垫圈。
- 拆卸螺栓 (3)。 卸下钟形吸油管组件 (8) 和管组件 (7)。 从管组件上拆卸 O 形密封圈。
- 卸下螺栓 (4)，然后从缸体上卸下发动机机油泵 (5)。
注: 拆卸发动机机油泵时不需要卸下盘 (9)。
Show/hide table
| |
| 图 1 | g01048711 |
Caterpillar Information System:
C9 Marine Auxiliary and Marine Generator Set Engines Speed Control (Switch) - Test
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Assemble
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Disassemble
C32 Marine Engine Plate Locations and Film Locations
C9 Marine Auxiliary and Marine Generator Set Engines Switch Circuits - Test
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C-15, C-16 and C-18 Truck Engines Pistons and Connecting Rods - Install
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Install
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Remove
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Guides - Remove and Install
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Seat Inserts - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
3524B Engines for 797 and 797B Off-Highway Trucks Cold Mode Operation
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C15 On-Highway Engine Engine Oil Pump - Disassemble
C15 On-Highway Engine Engine Oil Pump - Assemble
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
C9 Marine Auxiliary and Marine Generator Set Engines Air Inlet Heater Circuit - Test
2003/12/01 New Procedures Will Increase Power Module Reliability {7273}
C18 Marine Auxiliary Engines E096 High Fuel Pressure
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
C15 Engine Cooling System Coolant (DEAC) - Change
C15 Engine Cooling System Coolant (ELC) - Change
C15 and C18 Generator Set Engines Inlet and Exhaust Valves - Remove and Install