Engine Oil Pump - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
B     | 1P-0510     | 起子总成     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g01053962 |
- 利用工具 (B) 将套筒轴承 (11) 装入泵体中。 轴承接头应距两个轴承孔中心线 30 ± 15 度。 安装套筒轴承,使套筒轴承与泵体的外侧齐平。
- 最终组装前,检查机油泵所有零件的状态和技术规格。 请参阅技术规格, "机油泵"。
- 使用清洁的发动机机油润滑惰齿轮和驱动齿轮。 使用清洁的发动机机油润滑套筒轴承 (11) 。 将惰齿轮 (5) 和驱动齿轮 (4) 安装到泵体 (3) 中。
Show/hide table
图 2 | g01043546 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 安装盖 (10) 。 通过安装螺栓 (12) 将盖固定到泵体上。
注: 在组装后发动机机油泵必须能转动自如。 用手转动发动机机油泵。 如果发动机机油泵不能转动自如,重新安置盖 (10) 。
- 安装安全阀柱塞 (7) 、弹簧 (8) 、护圈 (9) 和螺栓 (6) 。
- 将键安装在轴上。
- 将驱动齿轮 (1) 安装到机油泵 (2) 的轴上。 安装螺栓 (13) 。 拧紧螺栓至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。
Show/hide table
图 3 | g01043619 |
End By: 安装发动机机油泵。 请参阅 拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
C15 On-Highway Engine Engine Oil Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
3524B Engines for 797 and 797B Off-Highway Trucks Cold Mode Operation
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C9 Marine Auxiliary and Marine Generator Set Engines Speed Control (Switch) - Test
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Assemble
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Disassemble
C32 Marine Engine Plate Locations and Film Locations
C9 Marine Auxiliary and Marine Generator Set Engines Switch Circuits - Test
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C-15, C-16 and C-18 Truck Engines Pistons and Connecting Rods - Install
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Install
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
C9 Marine Auxiliary and Marine Generator Set Engines Air Inlet Heater Circuit - Test
2003/12/01 New Procedures Will Increase Power Module Reliability {7273}
C18 Marine Auxiliary Engines E096 High Fuel Pressure
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
C15 Engine Cooling System Coolant (DEAC) - Change
C15 Engine Cooling System Coolant (ELC) - Change
C15 and C18 Generator Set Engines Inlet and Exhaust Valves - Remove and Install
G3500 Engines Detonation Sensors
C13, C15, and C18 Generator Set Engines E197 High Engine Oil Temperature
C9 Marine Auxiliary and Marine Generator Set Engines Diagnostic Codes
C18 Marine Auxiliary Engines E198 Low Fuel Pressure