Engine Oil Pump - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-2321     | 组合式拉拔器     | 1     |
B     | 1P-0510     | 起子总成     | 1     |
开始:
- 拆卸发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 拆卸"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 卸下将驱动齿轮 (1) 固定在发动机机油泵 (2) 泵轴上的螺栓。
Show/hide table
图 1 | g01001918 |
- 利用工具 (A) 将驱动齿轮 (1) 从轴上拆下。 从轴上卸下键。
- 拆下将护圈 (9) 固定到泵体 (3) 上的螺栓 (6) 。
Show/hide table
图 2 | g01043546 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 将护圈 (9) 、弹簧 (8) 和安全阀柱塞 (7) 从泵体上拆下。
- 将螺栓 (12) 和盖 (10) 从泵体上拆下。
注: 检查盖内的孔径。 铝盖没有轴承。 如果盖内的孔径损坏,则利用新件更换盖。
- 将惰齿轮 (5) 和驱动齿轮 (4) 从泵体上拆下。
- 利用工具 (B) 将套筒轴承 (11) 从泵体 (3) 上拆下。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
3524B Engines for 797 and 797B Off-Highway Trucks Cold Mode Operation
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C9 Marine Auxiliary and Marine Generator Set Engines Speed Control (Switch) - Test
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Assemble
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Disassemble
C32 Marine Engine Plate Locations and Film Locations
C9 Marine Auxiliary and Marine Generator Set Engines Switch Circuits - Test
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C-15, C-16 and C-18 Truck Engines Pistons and Connecting Rods - Install
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Install
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Remove
C15 On-Highway Engine Engine Oil Pump - Assemble
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
C9 Marine Auxiliary and Marine Generator Set Engines Air Inlet Heater Circuit - Test
2003/12/01 New Procedures Will Increase Power Module Reliability {7273}
C18 Marine Auxiliary Engines E096 High Fuel Pressure
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
C15 Engine Cooling System Coolant (DEAC) - Change
C15 Engine Cooling System Coolant (ELC) - Change
C15 and C18 Generator Set Engines Inlet and Exhaust Valves - Remove and Install
G3500 Engines Detonation Sensors
C13, C15, and C18 Generator Set Engines E197 High Engine Oil Temperature
C9 Marine Auxiliary and Marine Generator Set Engines Diagnostic Codes