NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
NOTICE |
---|
Handle the heat shields carefully. Do not tear the stainless steel foil inside the heat shields. Torn foil will let the insulation absorb flammable liquids and a fire can result from engine heat. |
- Remove front end cap (1) from the blanket for front manifold (2).
Show/hide table
Illustration 2 g01304216 - Remove assembly for rear blanket (3) from the blanket for front manifold (2).
Show/hide table
Illustration 3 g01304217 - Remove the bolts that secure the blanket for front manifold (2) to the front exhaust manifold section. Remove the blanket for front manifold (2) from the front exhaust manifold section.
Show/hide table
Illustration 4 g01304218 - Remove assembly for rear blanket (3) from intermediate end cap (4).
Show/hide table
Illustration 5 g01304219 - Remove assembly for rear blanket (3) from assembly for the blanket for turbocharger (5).
Show/hide table
Illustration 6 g01304220 - Remove assembly for the blanket for turbocharger (5) from the turbine housing.
Show/hide table
Illustration 7 g01304222 - Disassemble the blanket for the cap for turbocharger (6) and the blanket for the inlet housing for turbocharger (7).
Show/hide table
Illustration 8 g01304223 - Remove assembly for rear blanket (3) from rear manifold section (8).
Show/hide table
Illustration 9 g01304224 - Disassemble rear blanket (9) and the blanket for rear exhaust bellow (10).
Note: In order to remove the blankets, cut the stainless steel wire that secures the blankets.
Illustration 1 | g01304215 |
NOTICE |
---|
Do not use flammable liquid in order to clean the stainless steel foil inside of the heat shield. Use only water and detergent. Flammable liquid can saturate the insulation material and cause a fire when the engine temperature rises. |
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
NOTICE |
---|
Handle the heat shields carefully. Do not tear the stainless steel foil inside the heat shields. Torn foil will let the insulation absorb flammable liquids and a fire can result from engine heat. |
- Assemble rear blanket (9) and the blanket for rear exhaust bellow (10) with stainless steel wire.
Show/hide table
Illustration 11 g01304223 - Position assembly for rear blanket (3) over rear manifold section (8).
Show/hide table
Illustration 12 g01304222 - Assemble the blanket for the cap for turbocharger (6) and the blanket for the inlet housing for turbocharger (7) with stainless steel wire.
Show/hide table
Illustration 13 g01304220 - Position assembly for the blanket for turbocharger (5) over the turbine housing.
Show/hide table
Illustration 14 g01304219 - Install assembly for rear blanket (3) to assembly for the blanket for turbocharger (5) with stainless steel wire.
Show/hide table
Illustration 15 g01304218 - Install assembly for rear blanket (3) to intermediate end cap (4) with stainless steel wire.
Show/hide table
Illustration 16 g01304217 - Position the blanket for front manifold (2) over the front exhaust manifold section. Install the bolts.
Show/hide table
Illustration 17 g01304216 - Install assembly for rear blanket (3) to the blanket for front manifold (2) with stainless steel wire.
Show/hide table
Illustration 18 g01304215 - Install front end cap (1) to the blanket for front manifold (2) with stainless steel wire.
Illustration 10 | g01304224 |