Emergency Stopping
Show/hide table
若在緊急熄火之後的15分鐘之內打開曲軸箱的蓋子,瞬時點火會導致人員受傷。 在修正造成熄火的原因之前,請勿重新啟動引擎。 |
Show/hide table
注意事項 |
---|
緊急關斷控制器只能在緊急情況下使用。 切勿使用緊急關斷裝置或控制器。 |
在引擎熄火後,對引擎提供外部支撐的任何系統均牢靠固定。
附註引擎出貨時隨附的接線箱和控制盤上各有一個緊急熄火按鈕。 其他額外的緊急熄火控制裝置則由船隻原廠負責。
Show/hide table
插圖 1 | g00104303 |
典型的緊急熄火按鈕 |
引擎正常運轉時,緊急熄火按鈕在OUT位置。 若需緊急停機,請按下緊急熄火按鈕。 這會關閉供給引擎的燃油。 同時也致動了空氣關斷裝置 (如有配備) 。
附註有些船舶引擎配備的是一個必須拉出,才能使引擎停機的緊急熄火按鈕。
Show/hide table
注意事項 |
---|
在迫使緊急停機的問題已確定和校正前,切勿啟動引擎。 |
引擎控制開關、緊急熄火按鈕和進氣關斷裝置須在引擎重新起動前復位。 在復位緊急熄火按鈕前,先將引擎控制開關復位。
如欲將引擎控制開關復位,請將開關轉至"切斷/復位 (OFF/RESET)"位置。
如欲將緊急熄火按鈕復位,請以順時針方向轉動按鈕。 這個彈簧加力的按鈕將回復到OUT的位置。 也可以將按鈕拉出到OUT的位置。
如欲讓進氣關斷裝置復位,請將復位鈕轉到"OPEN"的位置。 確保兩個空氣關斷裝置均已復位。
Caterpillar Information System:
3508B, 3512B, and 3516B High Displacement Generator Sets Engine Electronics
3512C and 3516C Marine Auxiliary and Generator Set Engines Electrical System
2003/09/15 A New Integral Seal Provides Improved Sealing {7555}
C4.4 Industrial Engine Cooling System - Test
3606 and 3608 Engines Exhaust Manifold Shield - Remove and Install
Product Link MODEM Programming with Cat Electronic Technician (ET){7606, 7620} Product Link MODEM Programming with Cat Electronic Technician (ET){7606, 7620}
3508B, 3512B, 3516B, 3512C and and 3516C Auxiliary Engines, Generator Set Engines, and Generator Sets Safety Messages
C15 On-highway Engine Cylinder Head - Install
Pressure Requirements for the Fuel Transfer System{1256} Pressure Requirements for the Fuel Transfer System{1256}
Assembly Instruction for the New 3400 Oil Pump Body Serviced Assembly{1304} Assembly Instruction for the New 3400 Oil Pump Body Serviced Assembly{1304}
2003/09/01 Procedure for Connecting the Desired Speed Input from the Load Sharing Module {1264, 1408}
2003/09/01 Suspected Oil Leaks in the 3034 Engine Turbocharger {1052}
3508B, 3512B, and 3516B High Displacement Generator Sets Engine Stopping
3508B, 3508C, 3512B, 3512C, 3516B and and 3516C Marine Engines Product Lifting
2003/12/01 A New Integral Seal Provides Improved Sealing {7555}
C9 Industrial Engines Engine Oil Pressure Sensor
C3.3 Industrial Engine Crankshaft Wear Sleeve (Front) - Remove
C3.3 Industrial Engine Crankshaft Wear Sleeve (Front) - Install
C3.3 Industrial Engine Front Cover - Remove and Install
C3.3 Industrial Engine Housing (Front) - Remove
2003/11/01 The Alternator Guard has been Redesigned {7168}
2003/09/01 New Software Is Used on Product Link 151/201 {7606, 7620}
C15 On-Highway Engines Fuel System
2003/09/01 Improved Water Pump Seal {7555}