Crankshaft - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 8T-5096 | Dial Indicator Group | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Check the condition of the main bearings. Refer to Guideline For Reusable Parts, SEBF8009, "Main and Connecting Rod Bearings" or refer to Guideline For Reusable Parts, SEBV0544, "Engine Bearings and Crankshafts".
Note: The number six main bearing is the thrust bearing.
- Clean the bearing surfaces in the cylinder block for the main bearings. Apply clean engine oil on the upper main bearing. Do not put engine oil on the back side of the bearing surfaces. Install the upper main bearing in the cylinder block. Ensure that the tab on the back side of the bearing engages with the groove in the cylinder block.
Show/hide table
Illustration 1 g01128041 - Put clean engine oil on the journals of the crankshaft bearing. Attach a suitable lifting device onto crankshaft (1). The weight of crankshaft (1) is approximately
62 kg (136 lb) . Align the identification marks on the gear train. Carefully install crankshaft (1) in the cylinder block. - Clean the bearing surface of the main bearing caps. Install the lower main bearing in the crankshaft main bearing caps. Ensure that the tab on the back side of the bearing engages with the groove in the main bearing cap. Apply clean engine oil on the lower main bearing. Do not put engine oil on the back side of the bearing surfaces.
- Install crankshaft main bearing caps with the part numbers toward the right hand side of the cylinder block. Ensure that crankshaft main bearing caps have numbers 1 through 7. The numbers should start at the front of the engine. Place clean engine oil or Molylube on the bolt threads and the washers.
Note: When the bolts for the rear main bearing cap are tightened, slide the main bearing cap as far forward as possible until the cap is against the bolts. Hold the main bearing cap in this position and tighten the bolts.
- Install bolts (2) for main bearing caps (3). Tighten bolts (2) to a torque of
54 ± 7 N·m (40 ± 5 lb ft) . - Turn bolts (2) for an additional 90 ± 5 degrees (1/4 turn).
- Check the end play of crankshaft (1) with Tooling (A). The end play must be
0.07 mm to 0.32 mm (0.003 inch to 0.013 inch) .
Show/hide table
NOTICE |
---|
Ensure that the crankshaft main bearing tabs engage with the grooves in the block and the crankshaft main bearing cap. |
End By:
- Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
- Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
- Install the connecting rod bearings. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install".
Caterpillar Information System:
C7 Marine Engines Crankshaft - Remove
C7 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
C7 and C9 On-Highway Engines Engine Speed/Timing Sensor - Calibrate
G3304 and G3306 Engines Crankshaft Front Seal and Wear Sleeve - Install
C7 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
C7 Engines for Combat and Tactical Vehicles System Overview
C7 On-highway Engine Connecting Rod Bearings - Install
3044C Industrial Engine Engine Oil and Filter - Change
C7 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove
G3304 and G3306 Engines Crankshaft Front Seal and Wear Sleeve - Remove
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
G3304 and G3306 Engines Vibration Damper and Pulley - Install
C7 Engines for Combat and Tactical Vehicles Customer Specified Parameters Table
C7 Engines for Combat and Tactical Vehicles Customer Specified Parameters Worksheet
C7 On-Highway Engine Unit Injector Hydraulic Pump - Remove
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
G3304 and G3306 Engines Engine Support - Remove and Install
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C7 On-Highway Engine Engine Oil Filter Base and Oil Cooler - Install
C7 Engines for Caterpillar Built Machines Crankshaft Gear - Remove and Install
3500B and 3500C Marine Propulsion Engines Air Shutoff System
3500B and 3500C Marine Propulsion Engines Analog Sensor Supply
3500B and 3500C Marine Propulsion Engines Cat Data Link
3500B and 3500C Marine Propulsion Engines CAN Data Link