Crankshaft Front Seal and Wear Sleeve - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tooling     | Part Number     | Description     | Qty     |
A     | 5P-7299 (1)     | Installer     | 1     |
438-9547 (2) | Installer     | 1     | |
7F-8022 | Bolt     | 1     | |
4B-4283 | Washer     | 1     | |
B     | 4C-9500     | Quick Cure Primer     | 1     |
C     | 9S-3265     | Compound     | 1     |
Show/hide table
( 1 ) | Use to install 9Y-9895 seal |
( 2 ) | Use to install 362-8853 seal |
Note: The wear sleeve and the seal must be installed together.
- Apply clean engine oil on the seal lip and on the outside diameter of wear sleeve (1) . Install the seal on the wear sleeve with the lip of the seal toward the side of the wear sleeve that has the chamfer on the inside diameter, as shown.
Show/hide table
Illustration 1 | g00988346 |
- Use Tooling (B) in order to remove any oil from inside Diameter (X) of the wear sleeve and surface (Y) of the crankshaft.
Show/hide table
Illustration 2 | g00988347 |
- Apply Tooling (C) to Surfaces (X) and (Y) .
- Install the seal and wear sleeve (1) on the crankshaft with the lip of the seal toward the engine, as shown.
- Install Tooling (A) , as shown. Place lubricant between the bolt head and the installer.
- Use Tooling (A) in order to push the seal and wear sleeve (1) on the crankshaft. Push the installer until the installer is against the end of the crankshaft. The wear sleeve and the seal are now in the correct location.
- Remove Tooling (A) .
End By: Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Install" for the engine that is being serviced.
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
C7 Engines for Combat and Tactical Vehicles System Overview
C7 On-highway Engine Connecting Rod Bearings - Install
3044C Industrial Engine Engine Oil and Filter - Change
C7 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove
G3304 and G3306 Engines Crankshaft Front Seal and Wear Sleeve - Remove
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
G3304 and G3306 Engines Vibration Damper and Pulley - Install
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C15 On-Highway Engines Lubrication System
3044C Industrial Engine Cooling System Coolant (DEAC) - Change
3044C Industrial Engine After Stopping Engine
C7 and C9 On-Highway Engines Engine Speed/Timing Sensor - Calibrate
C7 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
C7 Marine Engines Crankshaft - Remove
C7 Marine Engines Crankshaft - Install
C7 Engines for Combat and Tactical Vehicles Customer Specified Parameters Table
C7 Engines for Combat and Tactical Vehicles Customer Specified Parameters Worksheet
C7 On-Highway Engine Unit Injector Hydraulic Pump - Remove
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
G3304 and G3306 Engines Engine Support - Remove and Install
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C7 On-Highway Engine Engine Oil Filter Base and Oil Cooler - Install
C7 Engines for Caterpillar Built Machines Crankshaft Gear - Remove and Install