Fuel Injection Pump - Install - Delphi DP210
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 230-6284     | 正时销 (凸轮轴)     | 1     |
B     | 230-6283     | 正时销 (曲轴)     | 1     |
C     | 9U-6198     | 曲轴转动工具     | 1     |
D     | 1U-6396     | O 形圈组装固定胶     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (C) 确保 1 号气缸处于压缩冲程上止点。 请参阅测试和调整, "燃油喷油正时 - 检查"。
注: 穿过凸轮轴齿轮安装工具 (A) 。 穿过曲柄臂安装工具 (B) 。
- 使用工具 (D) 润滑 O 形密封圈 (10) 。 将新的 O 形密封圈 (10) 安装到喷油泵上。
Show/hide table
图 1 | g00956267 |
- 将新垫圈安装到螺栓 (13) 上。
- 对齐喷油泵中的孔与前齿轮室中的孔。 将喷油泵安装到壳体上。
注: 在安装螺栓之前,应用手支撑喷油泵。
- 安装螺栓 (13) 。 拧紧螺栓 (13) 至扭矩为22 N·m (16 lb ft)。
- 将支架 (11) 定位到缸体上。 安装螺栓 (15) 并用手拧紧。
- 安装螺栓 (12) 和螺母 (14) ,用手拧紧。
- 拧紧螺栓 (12) 和螺母 (14) 至扭矩为 22 N·m (16 lb ft)。 拧紧螺栓 (15) 至扭矩为 44 N·m (32 lb ft)。
注: 确保在拧紧支架螺栓时喷油泵不受应力。
- 将喷油泵齿轮 (9) 定位到喷油泵轴上。 安装垫圈和螺母 (8) 。 逆时针方向转动喷油泵齿轮来消除齿隙。 拧紧螺母 (8) 至扭矩 24 N·m (17 lb ft)。
Show/hide table
图 2 | g00956200 |
注: 确保喷油泵齿轮与喷油泵轴的配合面清洁。 润滑喷油泵轴的螺纹。 螺母必须转动自如,直到与喷油泵齿轮形成接触。
- 将线束组件连接到正时提前电磁阀 (7) 上。
Show/hide table
图 3 | g00956204 |
- 连接线束组件 (2) 。 连接燃油管 (3) 。
- 连接回油管 (1) 。 将管组件 (4) 连接到喷油泵上。
- 松开螺栓 (5) 。 移动隔套 (6) ,以防止螺栓 (5) 紧固在喷油泵的轴上。 拧紧螺栓 (5) 至扭矩为 12 N·m (106 lb in)。
注: 必须正确定位隔套 (6) 并紧固螺栓 (5) ,以防止螺栓接触到喷油泵的轴。
- 拧紧螺母 (8) 至扭矩 88 N·m (65 lb ft)。
Show/hide table
图 4 | g00992965 |
- 拆下工具 (A) 和工具 (B) 。
End By:
- 安装前盖。 请参阅 拆解和组装, "前盖 - 拆卸和安装"。
- 安装曲轴皮带轮。 请参阅 拆解和组装, "曲轴皮带轮 - 拆卸和安装"。
- 安装喷油管。 请参阅 拆解和组装, "燃油喷油管路 - 拆卸和安装"。
- 如有装配,安装空气压缩机。 请参阅 拆解和组装, "空气压缩机 - 拆卸和安装"。
Caterpillar Information System:
3054C Industrial Engine Fuel Injection Pump - Remove - Delphi DP210
C9 Marine Engines Air Inlet Heater Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Accelerator Pedal (Throttle) Position Sensor Circuit - Test
3056E Industrial Engine Connecting Rod Bearing Journal
3056E Industrial Engine Electrical System
C9 Marine Engines Injection Actuation Pressure Sensor - Test
3500B Engines Air Shutoff
C9 Marine Engines and C9 Marine Generator Sets Exhaust Manifold - Remove and Install
3054C Industrial Engine Fuel Injection Nozzles - Install
3044C Industrial Engine Battery - Replace
C11 and C13 Engines for Caterpillar Built Machines Fuel System Pressure - Test
3054C Industrial Engine Fuel Injection Nozzles - Remove
C15 and C18 Petroleum Generator Sets Generator Load - Check
3406E and 3456 Generator Set Engines Speed/Timing Sensor
3044C Industrial Engine Overhaul Considerations
3500B and 3500 Marine Propulsion Engines with EUI Option Engine Valve Lash - Adjust
C15 On-Highway Engine Flywheel
C9 Marine Engines and C9 Marine Generator Sets Water Temperature Regulator - Remove and Install
3500B and 3500 Marine Propulsion Engines with EUI Option Fuel Injector - Adjust
C15 On-highway Engine Piston Cooling Jet
Installation Instructions for the 9W-1494 Service Meter Kit {7478} Installation Instructions for the 9W-1494 Service Meter Kit {7478}
C9 Marine Engines and C9 Marine Generator Sets Fuel Priming Pump - Remove and Install
C18 Marine and Marine Generator Set Engines Engine Oil Pan
3054E Industrial Engine Engine Oil Pan - Remove and Install