Fuel Injection Pump - Remove - Delphi DP210
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 230-6284     | 正时销 (凸轮轴)     | 1     |
B     | 230-6283     | 正时销 (曲轴)     | 1     |
B     | 230-6283     | 正时销 (曲轴)     | 1     |
C     | 9U-6198     | 曲轴转动工具     | 1     |
D     | 1P-2320     | 组合式拉拔器     | 1     |
ZZ     | 9U-7067     | 盖     | 2     |
9U-7069 | 盖     | 2     |
开始:
- 拆下燃油喷油管。 请参阅拆解和组装, "燃油喷油管路 - 拆卸和安装"。
- 拆下曲轴皮带轮。 请参阅拆解和组装, "曲轴皮带轮 - 拆卸和安装"。
- 拆下前盖。 请参阅拆解和组装, "前盖 - 拆卸和安装"。
- 拆下空气压缩机(如果配备)。 请参阅拆解和组装, "空气压缩机 - 拆卸和安装"。
注: 维修数据:拆卸和安装中的工具 (ZZ) 将不在图示中列出。 显示这一工具是为了协助有经验的维修人员。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 用工具 (C) 确保 1 号气缸处于压缩冲程的上止点。 请参阅测试和调整, "找到 1 号活塞上止点位置"。
注: 穿过凸轮轴齿轮安装工具 (A) 。 将工具 (B) 安装在曲柄臂内。
- 松开螺栓 (5) 。 移动隔套 (6) ,以便将螺栓 (5) 拧紧抵到喷油泵的轴上。 逆时针方向转动喷油泵齿轮来消除齿隙。 将螺栓 (5) 拧紧到 17 N·m (13 lb ft) 的扭矩。
注: 必须拧紧螺栓 (5) ,以防喷油泵的轴发生转动。
Show/hide table
图 1 | g00956204 |
Show/hide table
注意 |
---|
油泵不在发动机上时,无论在任何情况下都不能松开锁紧螺栓。 如果轴发生移动,油泵的动态正时将会丢失。 重建正时必须由授权的 Delphi 代理商来完成,且该项费用将不在保修范围内。 |
- 断开回油管 (1) 。 从喷油泵上断开管组件 (4) 。
- 断开线束组件 (2) 。 断开燃油管 (3) 。
- 从提前正时电磁阀 (7) 上断开线束组件。
- 从喷油泵的轴上拆下螺母 (8) 和垫圈。
Show/hide table
图 2 | g00956200 |
- 安装工具 (D) ,然后拆下喷油泵齿轮 (9) 。
注: 不要从喷油泵轴上撬出喷油泵齿轮。
- 拆下螺母 (14) 。 拆下螺栓 (12) 。
Show/hide table
图 3 | g00956267 |
- 如有必要,从缸体上拆下螺栓 (15) 和托架 (11) 。
- 拆下螺栓 (13) 以便拆卸喷油泵。
- 从前壳体上拆下喷油泵。 从喷油泵上拆下 O 形密封圈 (10) 。
Caterpillar Information System:
C9 Marine Engines Air Inlet Heater Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Accelerator Pedal (Throttle) Position Sensor Circuit - Test
3056E Industrial Engine Connecting Rod Bearing Journal
3056E Industrial Engine Electrical System
C9 Marine Engines Injection Actuation Pressure Sensor - Test
3500B Engines Air Shutoff
C9 Marine Engines and C9 Marine Generator Sets Exhaust Manifold - Remove and Install
3054C Industrial Engine Fuel Injection Nozzles - Install
3044C Industrial Engine Battery - Replace
C11 and C13 Engines for Caterpillar Built Machines Fuel System Pressure - Test
3054C Industrial Engine Fuel Injection Nozzles - Remove
C15 and C18 Petroleum Generator Sets Fuel Conservation Practices
3054C Industrial Engine Fuel Injection Pump - Install - Delphi DP210
C15 and C18 Petroleum Generator Sets Generator Load - Check
3406E and 3456 Generator Set Engines Speed/Timing Sensor
3044C Industrial Engine Overhaul Considerations
3500B and 3500 Marine Propulsion Engines with EUI Option Engine Valve Lash - Adjust
C15 On-Highway Engine Flywheel
C9 Marine Engines and C9 Marine Generator Sets Water Temperature Regulator - Remove and Install
3500B and 3500 Marine Propulsion Engines with EUI Option Fuel Injector - Adjust
C15 On-highway Engine Piston Cooling Jet
Installation Instructions for the 9W-1494 Service Meter Kit {7478} Installation Instructions for the 9W-1494 Service Meter Kit {7478}
C9 Marine Engines and C9 Marine Generator Sets Fuel Priming Pump - Remove and Install
C18 Marine and Marine Generator Set Engines Engine Oil Pan