High Efficiency Orifice (HEO) Fuel Injectors Are Now Used For Service Repairs {1290}
- Marine Engines:
- 3116 (S/N: 4KG; 1SK)
- 3126 (S/N: 8NM; 6SR)
Description of Change: High Efficiency Orifice (HEO) fuel injectors are now used for service repairs on these marine engines. The HEO fuel injectors will produce lower amounts of exhaust soot than the fuel injectors that have been used on these marine engines in production and service repairs.
Adaptable To: The HEO fuel injectors should be used for service repairs on the marine engines that are listed above. Remanufactured fuel injectors are also available for the HEO fuel injectors.
Refer to the following table in order to determine the correct part numbers of the fuel injectors for your marine engine.
Show/hide table
Engine     | Rating     | Part number of the HEO Fuel Injector     | Part number of the Former Fuel Injector     | Part number of the Remanufactured HEO Fuel Injector     |
---|---|---|---|---|
3116     | 224 kW (300 hp)     | -     | 127-8228 (1)     | 0R-8465 (1)     |
3116     | 242 kW (325 hp)     |
162-0212     | 127-8230 (2)     | 0R-8463     |
3116     | 261 kW (350 hp)     |
162-0212     | 127-8230 (2)     | 0R-8463     |
3126     | 287 kW (385 hp)     |
162-0212     | 127-8230 (2)     | 0R-8463     |
3126     | 313 kW (420 hp)     |
162-0218     | 135-2581 (2)     | 0R-8633     |
Show/hide table
( 1 ) | This part is still available. This part should normally be used to service the 224 kW (300 hp) 3116 Marine Engines. The 162-0212 Fuel Injector or 0R-8463 Fuel Injector (Remanufactured) may be used if reduced levels of smoke are desired. |
( 2 ) | This part has been cancelled. |
Caterpillar Information System:
3176C and 3196 Marine Engines Coolant Level Sensor - Remove and Install
3176C and 3196 Marine Engines Engine Support (Front) - Remove and Install
G3304 and G3306 Engines Test Tools for the Cooling System
2000/02/01 New Method To Determine When To Clean The Aftercooler Core {1064}
3176C and 3196 Marine Engines Water Outlet Manifold - Install
2000/02/01 Revised Oil Level Gauge Calibration Chart for 3412E Marine Engines {1326}
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Engine Cranks but Will Not Start
3126B Engines Finding Top Center Position for No. 1 Piston
3176C and 3196 Marine Engines Water Outlet Manifold - Remove
3176C and 3196 Marine Engines Turbocharger Outlet Pressure Sensor - Remove and Install
3508B Industrial Engines Turbocharger
3176C and 3196 Marine Engines Heat Exchanger - Install
3176C and 3196 Marine Engines Inlet Air Temperature Sensor - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Air Inlet and Exhaust System
3512B Engine for SPF343, SPS343, and SPT343 Pumpers Diagnostic Codes
3176C and 3196 Marine Engines Service Meter - Remove and Install
3114, 3116, and 3126 Engines for Caterpillar Built Machines Fuel Priming Pump and Primary Fuel Filter - Remove and Install
3176C and 3196 Marine Engines Manifold Adapter - Remove and Install - Right Hand Engine Application
3508B Industrial Engines Output for the General System Alarm
3508B Industrial Engines Start Enable Output
3508B Industrial Engines Shutdown Notification Output
3114, 3116, and 3126 Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
3500B and 3500B High Displacement Generator Set Engines Air Shutoff
3500B and 3500B High Displacement Generator Set Engines Grounding Practices