Heat Exchanger - Install
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Attach lifting slings and a suitable lifting device to the heat exchanger (29). The weight of the heat exchanger and the bracket is 77 kg (170 lb).
Show/hide table
Illustration 1 | g00677696 |
- Install two spacers (28) on the bracket (29) .
- Lift the heat exchanger (25) into position.
Show/hide table
Illustration 2 | g00677687 |
- Install four bolts and washers (27) .
- Install hose (24) and tighten the clamp (26) .
- Install the regulator housing (23) .
Show/hide table
Illustration 3 | g00677675 |
- Install four bolts and the washers (20) .
- Install the hose (22) and tighten the clamp (21) .
- Connect the hose (16) .
Show/hide table
Illustration 4 | g00677660 |
- Tighten the clamp (18) .
- Connect the electrical connector (19) .
- Reposition two hoses (17) .
- Install two spacers (15) .
- Install two bolts and washers (14) .
- Connect hose (12) .
Show/hide table
Illustration 5 | g00677647 |
- Tighten clamp (11) .
- Install two bolts and washers (6) .
Show/hide table
Illustration 6 | g00677572 |
- Position the fuel filter base and the fuel filter element in the correct location and install the two bolts and washers (8) .
- Connect hose (9) .
- Connect hose (10) .
- Tighten clamp (7) .
- Connect hose (2) .
- Tighten clamp (5) .
- Connect two tubes (3) .
- Close valve (13) .
Show/hide table
Illustration 7 | g00677654 |
Caterpillar Information System:
2000/02/01 Solenoid Available To Service Hydrax Actuators {1259}
3114, 3116, and 3126 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
3176C and 3196 Marine Engines Heat Exchanger - Remove
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Can Not Reach Top Engine RPM
3516B Engine for Caterpillar Built Machines Symptoms
3500B Engines Engine Monitoring System
3176C and 3196 Marine Engines Exhaust Manifold - Remove and Install
3500B and 3500B High Displacement Generator Set Engines Cat Data Link
3176C and 3196 Marine Engines Air Cleaner - Remove and Install
3512B and 3512C Engines For Caterpillar Built Machines Load Feedback Capability
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Customer Parameters Worksheet
C15 and C18 Petrolem Generator Set Engines Factory Passwords
3508B Industrial Engines Turbocharger
3176C and 3196 Marine Engines Turbocharger Outlet Pressure Sensor - Remove and Install
3176C and 3196 Marine Engines Water Outlet Manifold - Remove
3126B Engines Finding Top Center Position for No. 1 Piston
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Engine Cranks but Will Not Start
2000/02/01 Revised Oil Level Gauge Calibration Chart for 3412E Marine Engines {1326}
3176C and 3196 Marine Engines Water Outlet Manifold - Install
2000/02/01 New Method To Determine When To Clean The Aftercooler Core {1064}
G3304 and G3306 Engines Test Tools for the Cooling System
3176C and 3196 Marine Engines Engine Support (Front) - Remove and Install
3176C and 3196 Marine Engines Coolant Level Sensor - Remove and Install
2000/07/01 High Efficiency Orifice (HEO) Fuel Injectors Are Now Used For Service Repairs {1290}