Customer Parameters Worksheet
Record the following information before you change any programmable parameter.
Show/hide table
Equipment ID     |     |
Engine Serial Number     |     |
Serial number for Electronic Control Module (ECM)     |     |
Fuel Ratio Contorl (FRC) Offset     |     |
Rated Fuel Position     |     |
Low Idle Speed     |     |
High Idle Speed     |     |
Fuel Correction Factor     |     |
Engine Cooling System     |     |
Cold Mode Cylinder Cutout     |     |
Identifier for Cat Data Link     |     |
Engine Acceleration Rate     |     |
Cooldown Speed     |     |
Engine Cooldown Duration     |     |
Engine Prelube Duration     |     |
Crank Duration     |     |
Maximum Number Of Crank Cycles     |     |
Crank Terminate Speed     |     |
Air Shutoff     |     |
Ether Control     |     |
Fuel Position Multiplier     |     |
Record the following information from the engine information plate.
- Engine serial number
Record the following information from the engine monitoring system. The engine monitoring system can be accessed through the Caterpillar Electronic Technician (ET). Select "Monitoring System" from the "Service" menu.
Low System Voltage
Show/hide table
Warning Trip Points     |     |
Warning Delay Time     |     |
Low Engine Oil Pressure
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Shutdown Trip Point     |     |
Shutdown Delay Time     |     |
High Coolant Temperature
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Derate Trip Point     |     |
Derate Delay Time     |     |
Shutdown Trip Point     |     |
Derate Delay Time     |     |
Low Coolant Temperature
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Engine Overspeed
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Shutdown Trip Point     |     |
Shutdown Delay Time     |     |
High Air Filter Restriction Pressure
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Derate Trip Point     |     |
Derate Delay Time     |     |
Altitude (Atmospheric Pressure)
Show/hide table
Derate Trip Point     |     |
High Exhaust Temperature
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Derate Trip Point     |     |
Derate Delay Time     |     |
High Engine Oil Filter Restriction Pressure
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
High Fuel Filter Restriction Pressure
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
High Crankcase Pressure
Show/hide table
Warning Trip Point     |     |
Derate Trip Point     |     |
Derate Delay Time     |     |
Warning Delay Time     |     |
Shutdown Trip Point     |     |
Shutdown Delay Time     |     |
High Aftercooler Temperature
Show/hide table
Warning Trip Point     |     |
Warning Delay Time     |     |
Derate Trip Point     |     |
Derate Delay Time     |     |
Shutdown Trip Point     |     |
Shutdown Delay Time     |     |
Caterpillar Information System:
C15 and C18 Petrolem Generator Set Engines Factory Passwords
3176C and 3196 Marine Engines Aftercooler - Install
Replacing the Transformer in the Automatic Transfer Switch{4469} Replacing the Transformer in the Automatic Transfer Switch{4469}
3176C and 3196 Industrial Engines Cylinder Head - Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Check Engine Lamp Circuit - Test
3176C and 3196 Marine Engines Aftercooler - Remove
G3406 Engine Charging System
2000/02/01 Correction to Guideline for Reusable Parts and Salvage Operations, SEBF8192-02 {1201}
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Warning Lamp Circuit - Test
3176C and 3196 Marine Engines Transmission Oil Cooler - Remove and Install
3500B High Displacement Locomotive Engines Camshaft
3500B High Displacement Locomotive Engines Crankshaft
3512B and 3512C Engines For Caterpillar Built Machines Load Feedback Capability
3176C and 3196 Marine Engines Air Cleaner - Remove and Install
3500B and 3500B High Displacement Generator Set Engines Cat Data Link
3176C and 3196 Marine Engines Exhaust Manifold - Remove and Install
3500B Engines Engine Monitoring System
3516B Engine for Caterpillar Built Machines Symptoms
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Can Not Reach Top Engine RPM
3176C and 3196 Marine Engines Heat Exchanger - Remove
3114, 3116, and 3126 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
2000/02/01 Solenoid Available To Service Hydrax Actuators {1259}
3176C and 3196 Marine Engines Heat Exchanger - Install
3508B Industrial Engines Turbocharger